Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - ricardo1967

Pages: [1] 2 3 ... 37
1
Matt Shaff's Engine Shop / Re: New Keith Black block
« on: March 04, 2018, 07:18:55 AM »
Real beauty! Keep us posted.

2
Your Builds / Photo Gallery / Re: Debut "Elijha's Chariot" FED
« on: February 19, 2018, 03:52:26 PM »
Nice car, great story!

3
Your Builds / Photo Gallery / Re: Glenn's dragster thread
« on: January 30, 2018, 09:21:43 PM »
I'm fan of your videos Glenn. Also like the pace and tone of your narration  8)

4
Drag Racing / Re: Englishtown Raceway Abruptly Closes Its NHRA Drag Strip
« on: January 18, 2018, 12:36:39 PM »
love that video. no weight on front axle. no wheelie bars. no problems.  ;D ;D
too bad they don't make tires like that anymore. would love to do smokey shows for the crowds.
Amen brother!

5
Drag Racing / Re: Englishtown Raceway Abruptly Closes Its NHRA Drag Strip
« on: January 17, 2018, 03:19:34 PM »
I've never been there but it's really sad to see another historical dragstrip shutting down.

Drag racing is at risk of becoming an endangered sport. It's boring to watch, and to a point, boring to race.

Quote
That these drift events are continuing while drag racing is shutting down is an interesting gauge of the state of motorsports in America in 2018.

Isn't ironic that as drag racing practically eliminated tire smoke, the popular sport of the day is clouded with tire smoke? I'm for one totally against track treatment. In my opinion, it doesn't matter how fast you go, what matters (for driver and audience satisfaction), is how you go.

I get more chills watching this short video clip more than watching any modern Top Fuel doing a pass:

6
Front Engine Dragsters / Re: Grow Nostalgia Racing.
« on: November 10, 2017, 06:48:22 PM »
The Indianapolis based Nostalgia Pro Comp Association (NPCA) was awesome, it's a petty was short lived.

7
Tow Vehicles / Re: Box behind cab on 70s era funny car truck
« on: November 08, 2017, 03:26:54 PM »
Could it be a primitive bunk? (sleeping quarters)

8
Roo Man's Room / Re: suggestions for drive shaft protection
« on: October 30, 2017, 02:27:33 PM »
Those a  band clamps in the 4 size are difficult to find also, or at least they are for less than $100 ea.
Paul,
R.G. Ray clamps (top tier manufacturer) can be found on eBay for much less than that.

9
Your Builds / Photo Gallery / Re: Hello From Iowa!!!
« on: October 14, 2017, 05:18:27 AM »
Really cool intro, welcome to this honorable FED forum!

10
Your Builds / Photo Gallery / Re: The RainMaker
« on: October 10, 2017, 09:37:23 AM »
Nice ride Rainmaker. I was there, as a spectator.

11
Electronics / Re: fuel pressure sensor(s)
« on: September 27, 2017, 09:59:13 AM »
Dean,

Yes you will see pulsing, but that can be even out by inputting the correct frequency that the sensor is designed for. I don't know about other systems, but we use an early version of the Edelbrock QuikData (Serial #0014) which allows you to adjust the frequency.

While I am comfortable using this system, I would recommend an RPM Performance Data Logger because it is cost effective and the after sales service is outstanding.
Gino,
What would cause the fuel pressure pulses? Pump impeller?

12
Electronics / Re: fuel pressure sensor(s)
« on: September 26, 2017, 04:35:14 PM »
We drilled and tapped the plug on the distribution block at the back of the Enderle Hat for the same reason 32bantum did.

i talked to guy this weekend and asked about FP sensor location.  i asked about the distribution block. he said that his data log showed a lot of fluctuation here.  i think they do as 32bantam does. 

do you see any fluctuations on your logs if you have a logger?   im guessing it might be pulses from cylinder fill.  idk, just a guess.  you would think there would be consistent pressure there but that distribution block is feeding 8 cyl so could be some pulsing maybe

ty
dean

Mechanical constant flow fuel injection... I expect no pressure pulsing.

13
Spud Miller's Cave / Re: A little nitro results
« on: September 26, 2017, 02:49:21 PM »
Cool beans Bill, thanks for sharing the results. I guess you need to update your Your Best Time in your avatar  8)

It'll take self control to stop at 12%... another prospective candidate joining the Nitroalcoholics Anonymous group soon...  ;D

Did the engine get to sound a little different with the 12% nitro blend?


14
Your Builds / Photo Gallery / Re: new experiences - my 225" fed
« on: September 04, 2017, 11:41:26 AM »
Nice ride and hemi Noslin, congratulations! Keep us posted.

15
Roo Man's Room / Re: Building New FED 170" Need a little help
« on: August 15, 2017, 04:44:24 AM »
Thank you for posting those links. I appreciate it.
You're most welcome Scott. We do whatever takes to get FEDs on the strip.

I have a group on FB called "History of JR Fuel" https://www.facebook.com/groups/707306692694561/
Very nice! Subscribed.

Pages: [1] 2 3 ... 37