« previous next »
Pages: 1 ... 41 42 [43] 44 45 ... 77   Go Down

Author Topic: What did you do on your Front Engine Dragster TODAY?  (Read 813707 times)

Offline janjon

  • Full Member
  • ***
  • Posts: 208
    • View Profile
  • Your Best Time: 5.74/124 1/8
  • Your Engine: SB Chev, gas, 350ish
  • Your Track: Houston Motorsports Park
  • Your Vehicle: '65-ish 150" SBC/Glide FED
Re: What did you do on your Front Engine Dragster TODAY?
« Reply #630 on: March 26, 2014, 07:09:24 AM »
I don't know for sure, might have to remove axles and center section. Sooner or later, will have to find out...
Logged
Just keep the same amount of stuff on the right
as there is on the left. Seeing straight ahead is highly overrated....

Offline Dolmetsch

  • Sr. Member
  • ****
  • Posts: 348
    • View Profile
  • Your Best Time: dont bother with times anyome (last 4 years) just
  • Your Engine: 225 slant six Dodge . 246 cubes on 94 octane
  • Your Track: Picton Airfield
  • Your Vehicle: The Senior Dragster
Re: What did you do on your Front Engine Dragster TODAY?
« Reply #631 on: March 30, 2014, 11:36:03 AM »
Well it was yesterday but I put the heat on in the garage and set about moving the tranny cooler up so I can install the new tunnel ram with its attached headers. Or spring race date for Picton Airfield is May 17. I want it all done and sorted out before then. I like to go to race, not fix. I imagine it will take some flogging to get it to run perfect.
don
Logged
SR Dragster, because old people need to have fun too!

Offline GlennLever

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 2058
    • View Profile
    • The Lever Family Site
  • Your Best Time: 1/4 mile 7.950 at 165 MPH
  • Your Engine: Pontiac 461 Alky Blown
  • Your Track: Empire Dragway, NY
  • Your Vehicle: Front Engine Dragster
Re: What did you do on your Front Engine Dragster TODAY?
« Reply #632 on: March 30, 2014, 12:11:50 PM »
Quote from: Dolmetsch on March 30, 2014, 11:36:03 AM
Well it was yesterday but I put the heat on in the garage and set about moving the tranny cooler up so I can install the new tunnel ram with its attached headers. Or spring race date for Picton Airfield is May 17. I want it all done and sorted out before then. I like to go to race, not fix. I imagine it will take some flogging to get it to run perfect.
don

Have you seen the new category? Six Cylinder Drag Vehicles http://www.frontenginedragsters.org/forum/index.php?board=29.0
Logged
Glenn R. Lever
Rochester, New York 14617-2012
My Cars https://www.lever-family-racing.com/

Offline Dolmetsch

  • Sr. Member
  • ****
  • Posts: 348
    • View Profile
  • Your Best Time: dont bother with times anyome (last 4 years) just
  • Your Engine: 225 slant six Dodge . 246 cubes on 94 octane
  • Your Track: Picton Airfield
  • Your Vehicle: The Senior Dragster
Re: What did you do on your Front Engine Dragster TODAY?
« Reply #633 on: March 31, 2014, 04:15:58 PM »
Trans-cooler deal completed. Tomorrow finish painting headers if it is warm enuf and begin the install for good. Kind of nervous. Always am with a new set up. Probably because I have no one to blame but me if it turns out to be crap. Am looking for between 30 and 40HP.  If I get it I may have to retire from driving as I am already in thrill overload as is. However as my cousin's husband Ebi in Germany told me in 2003. "Don, a little bit more is always possible" He was at the time a formula 1 race engine design engineer for BMW. Words to live by I think. In fact I printed it, framed it and hung it on the shop wall.
don
Logged
SR Dragster, because old people need to have fun too!

Offline Paul New

  • Hero Member
  • *****
  • Posts: 745
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: What did you do on your Front Engine Dragster TODAY?
« Reply #634 on: April 05, 2014, 09:37:08 PM »
Assembled the dragster engine today 4.125 x 3.625

Logged

Offline dusterdave173

  • Hero Member
  • *****
  • Posts: 638
    • View Profile
  • Your Best Time: 5.38in 1/8th
  • Your Engine: 355 CI SBC
  • Your Track: Mooresville, NC
  • Your Vehicle: CenPen 200 inch FED
Re: What did you do on your Front Engine Dragster TODAY?
« Reply #635 on: April 06, 2014, 06:55:59 AM »
Wow! A five feet tall SBC!! Looking good man!
Logged
I have always had a fascination with fast cars at the expense of more normal character development

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1910
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: What did you do on your Front Engine Dragster TODAY?
« Reply #636 on: April 06, 2014, 03:50:35 PM »
Quote from: Paul New on April 05, 2014, 09:37:08 PM
Assembled the dragster engine today 4.125 x 3.625



Make sure Glen sees this with the pulleys in right order.Bottom little small and top little big but at least they are in right order top to bottom.
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline GlennLever

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 2058
    • View Profile
    • The Lever Family Site
  • Your Best Time: 1/4 mile 7.950 at 165 MPH
  • Your Engine: Pontiac 461 Alky Blown
  • Your Track: Empire Dragway, NY
  • Your Vehicle: Front Engine Dragster
Re: What did you do on your Front Engine Dragster TODAY?
« Reply #637 on: April 06, 2014, 04:46:08 PM »
Quote from: wideopen231 on April 06, 2014, 03:50:35 PM
Quote from: Paul New on April 05, 2014, 09:37:08 PM
Assembled the dragster engine today 4.125 x 3.625



Make sure Glen sees this with the pulleys in right order.Bottom little small and top little big but at least they are in right order top to bottom.

Your being nasty.
Logged
Glenn R. Lever
Rochester, New York 14617-2012
My Cars https://www.lever-family-racing.com/

Offline janjon

  • Full Member
  • ***
  • Posts: 208
    • View Profile
  • Your Best Time: 5.74/124 1/8
  • Your Engine: SB Chev, gas, 350ish
  • Your Track: Houston Motorsports Park
  • Your Vehicle: '65-ish 150" SBC/Glide FED
Re: What did you do on your Front Engine Dragster TODAY?
« Reply #638 on: April 06, 2014, 06:40:52 PM »
Helmet bars!
Logged
Just keep the same amount of stuff on the right
as there is on the left. Seeing straight ahead is highly overrated....

Offline Paul New

  • Hero Member
  • *****
  • Posts: 745
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: What did you do on your Front Engine Dragster TODAY?
« Reply #639 on: April 06, 2014, 07:30:46 PM »
Quote from: wideopen231 on April 06, 2014, 03:50:35 PM
Quote from: Paul New on April 05, 2014, 09:37:08 PM
Assembled the dragster engine today 4.125 x 3.625



Make sure Glen sees this with the pulleys in right order.Bottom little small and top little big but at least they are in right order top to bottom.

I agree a little big on the top but I can not fit a larger pulley on the bottom... I am only spinning the blower 8%od it will run 6.60's at 206 with the powerglide I am switching out to a B&J and a clutch this season so want to start with an engine tune up I know!
Logged

Offline ricardo1967

  • Hero Member
  • *****
  • Posts: 578
    • View Profile
  • Your Best Time: No full pass yet.
  • Your Engine: Alky SBC 400
  • Your Track: Brown County Dragway (Bean Blossom, IN)
  • Your Vehicle: 173" FED
Re: What did you do on your Front Engine Dragster TODAY?
« Reply #640 on: April 06, 2014, 08:35:41 PM »
Quote from: Paul New on April 05, 2014, 09:37:08 PM
Assembled the dragster engine today 4.125 x 3.625



Paul, that's a nice looking mill! What's the blower brand and size if you don't mind?
Logged

Offline GlennLever

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 2058
    • View Profile
    • The Lever Family Site
  • Your Best Time: 1/4 mile 7.950 at 165 MPH
  • Your Engine: Pontiac 461 Alky Blown
  • Your Track: Empire Dragway, NY
  • Your Vehicle: Front Engine Dragster
Re: What did you do on your Front Engine Dragster TODAY?
« Reply #641 on: April 06, 2014, 08:37:20 PM »
I'm 38 percent under driven and run 162 at 8.00
Logged
Glenn R. Lever
Rochester, New York 14617-2012
My Cars https://www.lever-family-racing.com/

Offline grapro

  • Jr. Member
  • **
  • Posts: 71
    • View Profile
  • Your Track: edmonton
  • Your Vehicle: 184" FED
Re: What did you do on your Front Engine Dragster TODAY?
« Reply #642 on: April 07, 2014, 05:46:27 AM »
I finally got my car rolling, was a while but it is done now. Had to mount the intake on the block just to get the right feeling. Looking forward for the rest of the build.
Logged

dreracecar

  • Guest
Re: What did you do on your Front Engine Dragster TODAY?
« Reply #643 on: April 07, 2014, 08:03:22 AM »
Paul,
   Are you planning on running a crank support??? Thats a lot of overhang of the lower hub/pulley for a standard SBC snout.   just asking
Logged

Offline Paul New

  • Hero Member
  • *****
  • Posts: 745
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: What did you do on your Front Engine Dragster TODAY?
« Reply #644 on: April 07, 2014, 09:29:56 AM »
I didn't get that far Saturday yes I run a crank support and   a Bryant crank w/ BBC snout
Logged
Pages: 1 ... 41 42 [43] 44 45 ... 77   Go Up
« previous next »