Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - George

Pages: [1] 2 3 ... 35
1
Front Engine Dragsters / Re: Power+weight+time.
« on: January 19, 2019, 08:03:28 AM »
2011-2013 we ran a FED with SBC. Dynos numbers were  600 +. Car and driver were 1460#. Ran low 5s with good track and air in the 1/8th.

2
Spud Miller's Cave / Re: grounding mag
« on: January 05, 2019, 05:23:30 AM »
I have used the Flaming River combo master kill . Part No.: FR1010 . It was cable operated from the rear of the car. Also had a mag switch in the drivers area.

http://www.flamingriver.com/index.php/products/c0015/s0002/FR1010

3
Wanted to sell / Crankshaft gear for Donovan gear drive. SBC
« on: January 02, 2019, 01:36:39 PM »
Gear only . Crankshaft gear for Donovan gear drive. Small Block Chevy. $75. OBO Contact me at NHRAFAN1@comcast.net            Thank you. George

4
MSD PN 8132. It is used. In great condition. $50. Contact me at NHRAFAN1@comcast.net Thank you. George

5
All new. Model 5341 Vertex OAC magneto. Comes with 3.0, 6.6,6.8,7.0,7.2,7.4 chips and instruction sheet. Also has yellow cover on lens. $125. or best offer. Contact me at NHRAFAN1@comcast.net       Thanks. George

6
Wanted to sell / DRE custom Kevlar engine diaper SBC dragster
« on: January 01, 2019, 05:56:42 AM »
We bought this new from Dennis Ridgeway. It has a two buckle window in the left side for oil lines. It has never been dumped in. Its in excellent condition. Comes with absorbent pads. It was ran with a Milodon full length sump pan in a FED. $250 + shipping. E-mail me at NHRAFAN1@comcast.net          Thank you. George

7
Wanted to sell / MSD 12LT Pro Magneto system Chevy PN 7908
« on: January 01, 2019, 05:44:05 AM »
MSD Pro Magneto 12LT Chevy with adjustable collar PN 7908

Coil/points box PN 8105

MSD Pro Mag hold down clamp PN 7905

Replacement cap and rotor PN 7919

Tom Scott Hot Fire red 40 ohm wires SBC

Everything listed $2000. + shipping. We ran this on our SBC for several years. Mag and box were serviced by Electromotion a few years ago. E-mail me at NHRAFAN1@comcast.net      Thank you. George

8
Wanted to sell / New MSD Pro Mag Controller PN 8973
« on: December 31, 2018, 03:29:18 PM »
 I bought this a few years ago thinking I would need it and never did. So it is for sale . $500 and I pay shipping in the US with a pre pay. Thanks. George

9
Roo Man's Room / Re: Rearend Upright Strap Thickness Requirement
« on: December 19, 2018, 04:00:58 AM »
Buy into the SFI.                                  https://sfifoundation.com/

10
Wanted to sell / Hilborn 18 AS nozzles . Set of 8 . 3 1/2" long.
« on: December 12, 2018, 06:12:38 AM »
Set of 8 . Alky Digger and Speedway get $350. Asking $200. E-mail me at NHRAFAN1@comcast.net   Thanks. George in 62563.

11
Tow Vehicles / Re: Alcohol Engine with No Water
« on: November 28, 2018, 09:03:16 AM »
No argument with simplicity. I ran a stock block SBC ,stack injected setup on Methanol. The first year was dry. Freeze plugs were installed . We ran an immersion type heater in the oil pan. After consulting with a much smarter and experienced racer I installed 2 block heaters. One in each side. The engine loved the heat soak. It had more power and showed less fuel in the oil. The engine is now with another racer but if I were to do it again I would go with the water. We ran a fully filled Dart iron block with a blower combination and it always ran stronger after a run or 2. Methanol loves a warm engine. My 2 cents. George

12
Spud Miller's Cave / Re: Electric shift with Mag.
« on: September 25, 2018, 05:30:23 PM »
IMO the MSD magneto makes the electronics so easy. We have ran the MSD12LT for 8 years with a 2 step, rpm shifter and rev control. Very dependable and have a rpm playback.

13
Your Builds / Photo Gallery / Re: Glenn's dragster thread
« on: August 21, 2018, 07:47:00 PM »
Must be something left inside
Agree.

14
Spud Miller's Cave / Re: Stack Injector Net
« on: August 12, 2018, 03:42:19 PM »
A picture with the screen on the stacks.

15
Spud Miller's Cave / Re: Stack Injector Net
« on: August 12, 2018, 03:30:43 PM »
Dog poly door screen material with a bungee cord sewn into a the edge worked well with our stack setup.

Pages: [1] 2 3 ... 35