Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Topics - sandhopper2

Pages: [1] 2
Wanted to buy / wtb for 9" axles
« on: June 12, 2020, 08:51:35 AM »
Looking for some ford 9" axles with 31 spline cheap. I have a dragster project for sale and I need to get it to a roller to help with sale. I have the housing that has not been cut so length is not an issue they just need to be for dragster big ford
Would like to be 31 spline as that is the spool I have 

Wanted to buy / WTB small oil tank
« on: January 10, 2020, 10:52:14 AM »
Looking for a small oil tank 1 or 2 gal to use in a dry sump system

Your Builds / Photo Gallery / my new red RED
« on: September 07, 2019, 08:48:07 AM »
This is the new project will get the Turbo VW with PG trans

Wanted to sell / 205" RED project
« on: July 19, 2019, 04:39:23 PM »
I have a RED project with a lot of parts to complete would like to sell the lot , but will part out if it does not sell . CM chassis was last cert in 1992 sportsman class . I have a 9" ford rear housing that needs to be shortened and the jig to do that , no axles but I do have new disk brakes
Located in Norwalk Ca 90650 
asking $2400 or possible trade for ?

Wanted to buy / wtb pg torque converter
« on: May 28, 2019, 08:11:59 PM »
Looking for a torque converter with turbo spline around 5000 stall. must be close to me or able to ship and take paypal. I found one but the guy will not take paypal.

Wanted to buy / WTB 35 spline spool
« on: March 12, 2019, 04:47:24 PM »
Looking for a 35 spline standard spool and a coupler for standar 9 " 28 spline

Rear Engine Dragsters / mock up today
« on: February 27, 2019, 04:53:18 PM »
Got some work done today on Mockup engine to trans . 1/4 in motorplate to connect the VW to shorty powerglide. Looks like total lenght will be around 44" from pully to rear housing. Now I need to find the couplers to connect the trans to the Ford 9" rear.

Wanted to buy / couplers
« on: February 27, 2019, 04:44:22 PM »
Looking for couplers to connect Powerglide to ford 9" think total distance 4 to 6 "

Rear Engine Dragsters / adding tabs and other mounts
« on: February 01, 2019, 02:48:17 PM »
When adding mounting tabs to a CM chassis to the tabs need to be CM or can they be mild steel and do they need to be TIG welded or is MIG ok for this
I need to move the Brake and Gas peddles on my project

Rear Engine Dragsters / Replace the cage
« on: December 28, 2018, 09:24:29 AM »
Not sure if I can get some more room by replacing the cage , but any Idea how much it would cost ? It maybe easier to do the entire thing , but could just the front tube and the side tubes be replaced ? I'm in SOCAL

Rear Engine Dragsters / PG shifter small space
« on: December 27, 2018, 06:33:10 PM »
My dragster is small space in the cage what is a good shift unit to use , or is they a way to make one ?

Wanted to buy / WTB spindle mount front wheels/tires
« on: December 22, 2018, 05:55:15 PM »
Looking for front wheels and tires for a RED with anglia spindles . Budget build so looking for used
I'm in socal so local would be best

Rear Engine Dragsters / New project
« on: December 11, 2018, 07:37:04 PM »
Picked up a new to me old RED should be about 205 inch WB . Last cert # is spotsman 1992
I know it will be a lot of work , but that for me is 1/2 the Fun
Will ad some pictures when I figure that out

Wanted to buy / ford 9 inch rear end
« on: December 04, 2018, 09:47:41 AM »
Looking for a Ford 9" rear for a rear engine dragster project , or maybe someone that can shorten the one I have . I'm is Socal so loacl is best

Rear Engine Dragsters / rear engine dragster re cert in Ca
« on: September 27, 2018, 10:08:53 AM »
Looking at a dragster that has very old cert from 1992 , I know it will need some updates , but where in socal do you get the recert done and any ideas of the cost ? Do you need the engine in it ?

Pages: [1] 2