1
Roo Man's Room / Re: starter and mag switch
« on: December 15, 2013, 03:34:16 PM »
Hope this helps if not email me mike.coker09@gmail.com
FEDs Forever!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Roo Man's Room / Re: short or full body
« on: June 23, 2013, 01:16:00 AM »
Mr. Froggy I like the way you think.
3
Spud Miller's Cave / Re: Small amount of nitro or m5
« on: June 22, 2013, 03:28:24 PM »
'Spud,
Congratulations on your magazine article you deserve it. On the low amount of nitro issue Rich Barnard out of Ohio had a big block with aluminum heads and 12.5:1 compression on alky and best he ran was 8.16 and was frustrated with the performance of the car. I mixed him up 25% and right out of the box he went 8.02, 8.01 and on a 8.00 index run he went 7.96. Like you I don't recommend the nitro much with 14:1 compression. It did seem to me with the engine set to run nitro you gained a tenth for every 10% you added. I found it to be a good tuning tool.
coker
Congratulations on your magazine article you deserve it. On the low amount of nitro issue Rich Barnard out of Ohio had a big block with aluminum heads and 12.5:1 compression on alky and best he ran was 8.16 and was frustrated with the performance of the car. I mixed him up 25% and right out of the box he went 8.02, 8.01 and on a 8.00 index run he went 7.96. Like you I don't recommend the nitro much with 14:1 compression. It did seem to me with the engine set to run nitro you gained a tenth for every 10% you added. I found it to be a good tuning tool.
coker
4
Roo Man's Room / Re: short or full body
« on: June 21, 2013, 01:06:36 PM »
Yup Steve its Granddad hello to you too my friend.
5
Wanted to sell / New Comp cam roller lifters
« on: June 17, 2013, 04:45:19 PM »
COMP Cams 819-16 - COMP Cams Endure-X Roller Lifters
Lifters, Mechanical Roller, Vertical Link Bar, Chevy, Set of 16
Part Number: 819-16
Summit price $390.97
Again new never used call rick at 317-603-0832
Will sell for $200.00
Lifters, Mechanical Roller, Vertical Link Bar, Chevy, Set of 16
Part Number: 819-16
Summit price $390.97
Again new never used call rick at 317-603-0832
Will sell for $200.00
6
Wanted to sell / New Comp cam roller Rocker arms
« on: June 17, 2013, 04:43:55 PM »
Comp Cams: Rocker Arm; Ultra Pro Magnum; Rocker Arm; Stud 7/16 in. Ratio 1.7 in.; Chevy Big Block 396-454 cid; 16 pc.
Part Number: 1620-16
$319.97 Summit
Will sell for $175.00
New never used call Rick at 317-603-0832
Part Number: 1620-16
$319.97 Summit
Will sell for $175.00
New never used call Rick at 317-603-0832
7
Roo Man's Room / Re: short or full body
« on: June 14, 2013, 12:44:27 PM »
I like the short body on small block cars less weight and less maintenance between rounds.
If your a T/F car from the 60 then I prefer a full body.
If your a T/F car from the 60 then I prefer a full body.
8
Front Engine Dragsters / Re: what pump for nitro
« on: May 25, 2013, 03:13:05 PM »
I ran nitro in the 60's and recently from 2004-2008 in 372" dart little M. Best ET on 80% was 7.25 @ 189 and have all runs documented from 30% to 80% before the wheels came off.
Shoot me an email at mike.coker09@gmail.com if you want free info.
Shoot me an email at mike.coker09@gmail.com if you want free info.
Pages: [1]