Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - dusterdave173

Pages: 1 [2] 3 4 ... 9
16
Wanted to sell / INTERCOMP 0-15 TIRE GAUGE 4 INCH LIKE NEW
« on: May 22, 2019, 11:32:16 AM »
Almost brand new NICE big easy to see 4 inch diameter--very accurate  0-15 TP gauge these are $75 new get this one $50 shipped FREE  paypal OK  dusterdave173@gmail.com
sold car dont need anymore

17
Wanted to sell / KINSLER QUICK CHANGE JET CANNISTER & NEW HI SPEED CAN
« on: March 12, 2019, 11:43:06 AM »
Kinsler quick change jet can is $90 new--The new Hi Speed bleed off with shims is brand new never used and one extra pill can all -6   everything shown shipped Free $70 dusterdave173@gmail or 704 244 6649 Thanks

18
Wanted to sell / FRAMEWORKS SHIFTER FOR POWERGLIDE--CRAZY RARE!
« on: January 16, 2019, 07:52:40 AM »
Best dragster shifter out there for FED--have not been made in years! I found another one! These are the smallest , lightest. strongest little units ever made--this one comes with air shifter set up and long moorse cable--does not get any better!
$325 plus $20 freight  These are the BEST FED shifters ever made--very hard to find!!!!!!
You can take air deal off easy as pie for full manual and more period correct
dusterdave173@gmail.com   704 244 6649

19
Wanted to sell / WHEEL STUD SPACERS
« on: December 13, 2018, 06:56:31 AM »
 One set of 10 aluminum wheel stud spacers used on every dragster--goes on stud against wheel before nut---$25  .575 thick     shipped FREE  dusterdave173@gmail.com

20
Dan Dishon's Transmission Den / CONVERTER ID HELP
« on: December 04, 2018, 09:07:43 AM »
Scored an unknown 8 inch--well built--only stampings are on the center of the nose where it goes into crank it says
B26
2936
3
Just was not sure what company stamped them there --just working to ID this thing
Thanks for the help!!!!!!!!!!!!!!

21
Wanted to sell / -6AN T with HIGH SPEED LEAN OUT CAN NEW!
« on: November 27, 2018, 12:08:06 PM »
NEW! WITH ADJUSTER SHIMS THIS IS OVER $120 FORM MOST PLACES GET THIS BRAND NEW SET FOR $65 SHIPPED FREE   THANKS  dusterdave173@gmail.com or 704 244 6649

22
If you use the short pancake style this is you--You need a spare in the trailer always! new cost $128 get this brand new unit $60 shipped FREE  dusterdave173@gmail.com  or 704 244 6649

23
Front Engine Dragsters / SOLD MY CAR! THANKS TO ALL HERE FOR A GOOD RIDE!
« on: November 15, 2018, 11:07:08 AM »
Well---I sold my car--I started her from a pile of tube in 2011--What a labor of love--I built every inch of it myself , engine and all--Dreamed it--Built it--drove it--Loved it--Made lots of new friends and had a ball--but things change--life changes--I am retiring end of next year so I have been making lots of changes--The car is going to a great guy--he owns a drag strip in IL so it will see a lot more action and we are passing all the good Karma on to him and his family--
I wanted to take a moment and Thank every member here for all of the great advice--encouragement-etc

Hey the good news is you can check out the Wanted to Sell section and pick up some great deals on my left overs LOL!

I had a blast--ran a FED --Ran fast--Ran safe--and can put that in my list of happy things

Again--Thanks to all for this great community and this great website
Sincerely David Kluttz

24
Wanted to sell / PG TAILSHAFT HOUSINGS--GOOD SPARES
« on: November 11, 2018, 07:59:16 AM »
 I have two Powerglide std length tailshaft housings  Good to have a spare get both shipped FREE $45
dusterdave173@gmail.com or 704 244 6649   paypal OK on all my items listed if you eat the fees  Thanks David

25
Wanted to sell / SFI-15 SPARCO SUIT --LIKE BRAND NEW! DEAL!
« on: November 10, 2018, 07:51:52 AM »
sold it sold it sold it thanks!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!


hey gang--looks like I have my car sold--been a lot of fun but came time to move on
If you are planning a FED you will need a good firesuit--The cheap China jobs from Calif are all over but they are imported and well..they are not cheap either  a Good SFI-15 suit is expensive!
I have a LIKE NEW--FRESH as a daisy--ZERO soil-ZERO oil or stain--near perfect SPARCO X-LIGHT  These are the LIGHTEST suits on the market--They are the best quality made period! New from Biondo they are $1275 plus $60 for arm restraints plus shipping--I also have an expensive DRYER FAN HANGER to go with--has 6 n electric fan so when you hang suit it is blowing air inside and keeping things dry--This suit is LIKE new lovingly cared for
It is a Europe size 64 which is a USA 2x Chart says Chest 47 in, waist 44 in ( this is usually 2 in more than your jean size ), hip 48. height from 5ft 9 in to 6 ft 3 in   I am 5ft 11 in 238 and it is very comfortable--These suits have the best quality pockets, zippers etc out there--This suit will cover any application that is not blown--Biondo can recert these every five years for about $50 Try that on your import job
Face it you need the best on safety equipment--This is it--For a DEAL  The hanger is worth $100
Will take $900 OBO shipped FREE   I know you may be able to get into an import for same $$ but it is your skin we are talking about here  These are LIGHT, BREATHE and comfortable.
email me dusterdave173@gmail.com or phone 704 244 6649 eastern time

26
Running SBC 2.100 rod journals? I have one new in original packaging--from Callies
coated, narrow, dowel hole for aluminum rod ( can run on steel rods), chamfered in -.021
These are a life saver if you are adjusting bearing clearance --RARE not sure they make these anymore
$75 shipped Free   dusterdave173@gmail.com

27
New in original package--plates to install Hooker or Sthal pattern headers on std 23 degree SBC heads --these allow you to run header tubes bigger than 1 3/4 on std heads be it stock or any aftermarket aluminum--1 3/4 is biggest you can get on regular head --just port to match your head and header and works like a charm--Over $180 on Ebay etc
$50 shipped FREE!!!!!!!!  dusterdave173@gmail.com

28
Wanted to sell / VINTAGE MT VALVE COVERS VERY CLEAN
« on: October 19, 2018, 01:12:36 PM »
Vintage MT valve covers SBC
fresh blasted--very nice set
$50 plus actual UPS paypal ok
Thanks  dusterdave173@gmail.com

29
Wanted to sell / New King Pin Boss's
« on: October 17, 2018, 09:05:03 AM »
Two new King pin Boss's came with some Strange Brand spindles  $20 shipped FREE dusterdave173@gmail.com

30
Wanted to sell / 200 in FED Race Ready NICE car
« on: September 12, 2018, 06:55:28 AM »
Way too much to list here--fresh 355 CI aluminum rod engine--fresh Glide--NHRA certified to 7.50
well engineered, sanitary, race ready now--best tig weld job anywhere done by nuclear certified welder
wide cage 21 1/2 in plenty of room for any driver email me and I will call you back , go over everything, have to of pictures all the way back to pile of tube  attaching photos on this site is a chore so just email me  dusterdave173@gmail.com    Thanks!!
You get a deal on a roller and it will be a year until you have a well sorted car--and you will still have $15K min in it
Get this beautiful race ready car with lots of extras $14k  well equipped 24 ft enclosed available for great price if you but the car--
Thanks

Pages: 1 [2] 3 4 ... 9