946
Front Engine Dragsters / Re: What did you do on your Front Engine Dragster TODAY?
« on: July 21, 2013, 08:30:28 AM »
New set of valve springs this morning
FEDs Forever!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
947
Front Engine Dragsters / Re: specs for wing on FED
« on: July 20, 2013, 09:56:52 AM »
Most of the handling problems with my car are the rear tend's to walk around on the top end . The 12 inch tires don't help either . I think if you don't have it too far back it should be ok. NHRA makes all gas dragsters and econo dragsters run a rear wing . It has helped those cars a lot . Before the wing rule a lot of those cars were crashing especially the B/ED cars very light and small tires
948
Front Engine Dragsters / Re: It's official, I'm going sbc...............
« on: July 19, 2013, 10:52:40 AM »
All you have left to do is jack those injector's up and put a f.e.d. under them!!
949
Front Engine Dragsters / Re: specs for wing on FED
« on: July 19, 2013, 06:51:07 AM »
Really not that bad of an idea . I would like to hear what Roo's thought's would be about this . I don't think it would have that much of an effect on the front of the car but I do think it would make the car more stable at speed.
950
Front Engine Dragsters / Re: What did you do on your Front Engine Dragster TODAY?
« on: July 17, 2013, 01:57:51 PM »
Going to spend all weekend working on my car . Hope to be out testing in 2 weeks.
951
Rear Engine Dragsters / Re: What did you do on your Rear Engine Dragster TODAY?
« on: July 17, 2013, 11:16:19 AM »
We are going to hone it with the plates it should clean up ok.
952
Events / Re: 5th Annual DOVER DRAG STRIP NOSTALGIA DRAGS/Car Show Aug.10-11
« on: July 17, 2013, 11:13:00 AM »
This has been A summer to remember now it is wicked hot !
953
Rear Engine Dragsters / Re: What did you do on your Rear Engine Dragster TODAY?
« on: July 16, 2013, 05:54:49 PM »Thats why we always bought ten set of pistons,blower can do the same and worst.He wishes now that he had bought 10 It's going to be 3 to 4 weeks for a new piston
954
Rear Engine Dragsters / Re: What did you do on your Rear Engine Dragster TODAY?
« on: July 16, 2013, 05:51:02 PM »Port or plate nitrous?Fogger 2 systems
955
Rear Engine Dragsters / Re: What did you do on your Rear Engine Dragster TODAY?
« on: July 16, 2013, 02:26:26 PM »
This was on my son's car . We have been running nitrous for 5 years and never had a problem like this . We were trying to be on the safe side and ran it a little rich . It turns out that being too rich is worse than being too lean ! We are trying to figure this all out as we do not want this to happen again but as of right now we think it was too much fuel
956
Events / Re: 5th Annual DOVER DRAG STRIP NOSTALGIA DRAGS/Car Show Aug.10-11
« on: July 16, 2013, 02:17:48 PM »
I thought I would bump this up . Hope to see some of you there!
957
Front Engine Dragsters / Re: tortion front
« on: July 16, 2013, 02:11:19 PM »
Good looking car nice picture
958
Rear Engine Dragsters / Re: What did you do on your Rear Engine Dragster TODAY?
« on: July 16, 2013, 02:07:34 PM »
This is not good
959
Rear Engine Dragsters / Re: What did you do on your Rear Engine Dragster TODAY?
« on: July 14, 2013, 01:54:57 PM »
A little bit of a setback with my sons car . Leaked it down and had 60 percent leakage in 1 cylender took it apart and found crushed ring land . Too much fuel you can do more damage from too rich than too lean !
960
Front Engine Dragsters / Re: How do i get my chassis certified
« on: July 14, 2013, 08:34:38 AM »
Ricci You can get it done at any one of the divisional races . There is one at Epping next weekend . Also one at Englishtown and Atco . You don't have to be a competitor to get it done . Just call the division 1 office and they will let you know what day to bring it .