Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - racerken

Pages: [1] 2 3 4
Or call Alkydigger.  Mike will help you

Wanted to buy / Re: Seeking FED
« on: March 31, 2021, 08:58:41 AM »
Daniel,  My name is Ken Thibodeaux.  I live in gonzales.  I have a fed.  Friend me on facebook.  Lets talk. or call me. 225 281 5679

Wanted to buy / Re: Seeking FED
« on: March 30, 2021, 11:45:18 AM »
See that your track is No Problem.  Just wondering, who is  this.  We need more fed guys around here.

Dan Dishon's Transmission Den / Re: trans shield replacement
« on: June 28, 2019, 02:33:02 PM »
It's been awhile but I was not allowed to run an nhra division race once because I didn't have the lower shield.

Events / Re: Bowling Green 2019, who is going ?
« on: June 07, 2019, 11:01:59 AM »
Going to miss it.  First time in 5 years.  Going thru withdrawals already.  Sucks

Front Engine Dragsters / Re: reason you choose a FED?
« on: April 30, 2019, 04:36:01 PM »
Ran RED for years.  Quit for awhile and when I decided to get back into racing I thought back about when I had the most fun and it was when I first started racing back in the 70's racing a fed.

Your Builds / Photo Gallery / Re: new experiences - my 225" fed
« on: March 13, 2019, 02:50:20 PM »
Bruce,  not trying to be a smart ass but that sounds like a screwed up NHRA answer to the problem.  How can the bottles be mounted autside of the frame and the frame be first point of contact?

Electronics / Re: Wiring a relay
« on: February 21, 2019, 01:13:33 PM »
Thanks for the reply

Electronics / Wiring a relay
« on: February 19, 2019, 02:22:17 PM »
OK guys,  I am electrically challenged and need help.  I have a Dedenbear 2 Stage Throttle Stop Controller (Model TSC-2A)  that I want to use as a shift timer to activate a shifter solonoid.  I can't figure out how to wire in the  30amp 5 pin relay. Any help would be appreciated.  Thanks, Ken 

Spud Miller's Cave / Re: fuel tank vent size
« on: February 07, 2019, 03:02:52 PM »
Dusterdave.  That is why I run my loups horazontal  rather than vertical .

The way it was meant to be, until the mighty dollar got involved,  like all of drag racing.  Glad you guys are having fun and not spending your retirement fund racing.

Wanted to buy / Re: Shift Timer
« on: December 29, 2018, 09:30:08 AM »
Thanks, and Happy New Years.

Wanted to buy / Re: Shift Timer
« on: December 28, 2018, 02:33:10 PM »
Thanks for the response Bill.  Actually I think I have one of these that I took off of a super comp. car I bought quite awhile ago.  I will have to dig it out.  So you are saying I should be able to hook this to my trans brake button and it will activate the shifter solonoid.based on the amount of time I program into it and not by rpms? 

Wanted to buy / Shift Timer
« on: December 28, 2018, 11:08:27 AM »
WANT TO BUY.  Dedenbear ST1  to activate shifter by time rather than RPM.  Someone out there must have one they are not using and wants to get rid of.  Thanks

Tow Vehicles / Re: Towing in the pits
« on: November 12, 2018, 10:32:13 AM »
Never had an issue towing.  We use a strap to tow back to the pits after a run.  However, we do use a push bar and golf cart to push to the staging lanes. Just because that is the way they did it back then.

Pages: [1] 2 3 4