Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - hemidakota

Pages: [1] 2 3 ... 14
1
Spud Miller's Cave / Re: compression with higher dosage of nitro
« on: October 19, 2021, 07:46:59 AM »
Where do you get your pistons from? I live on the west coast Chris so I have a lot of venders here in my city of carson city nevada. Icon is a place here that I have alot of family at, they make the best skirt design in the industry and customer support is great, if anyone wants to talk pistons call Icon 775-882-7790

2
Front Engine Dragsters / Re: Front Tires Popping out of the Beams.
« on: October 17, 2021, 09:48:38 AM »
What does the front end weigh? My FED has never been on the track but I have been told the front should weigh approx 375 to 400 lbs to work correctly. Think Frank Parks told me that...

3
Spud Miller's Cave / Re: compression with higher dosage of nitro
« on: August 08, 2021, 09:10:47 PM »
Love it, Intake Valves kissing the pistons in every hole...

4
Spud Miller's Cave / Re: compression with higher dosage of nitro
« on: July 13, 2021, 04:34:40 AM »
There is a local clutch guy that runs an afuel car, compression is not an issue from what they say...Love to learn about all this stuff

5
Matt Shaff's Engine Shop / Re: Compression for FED
« on: April 02, 2021, 09:38:16 PM »
If you have a small cc head you should still be able to get at least 11 to 1 out of it ! When I started messing around with 20 percent nitro I went to a flat top piston to drop compression down ! To my surprise it really didn't slow down much on straight alcohol ! The best it ever ran on the higher compression straight alky was 7.24 and with the lower compression straight alky 7.32 ! If you need to make a little more power just put a little nitro 10 to 15 percent and that will wake it up !
How much of a compression change and from how high of compression? Just interested, thanks

6
Dan Dishon's Transmission Den / Re: Bushing or Needle Bearing
« on: January 07, 2021, 04:50:38 PM »
Thanks everyone, I have a hardened coupler for needle brg. so that is what i will use.

7
Spud Miller's Cave / Re: Mag drive
« on: January 05, 2021, 01:23:46 PM »
Found one, Thanks Spud...

8
Spud Miller's Cave / Mag drive
« on: January 05, 2021, 10:09:31 AM »
Who makes a straight drive to run a mag off of front of cam, KB gear drive, do not want a fuel pump drive just a mag drive. Is there anything like this out there? Im having a hard time finding just a mag drive. Thanks all.

9
Front Engine Dragsters / 2021
« on: January 01, 2021, 06:29:33 AM »
Happy New Year Everyone!

10
Dan Dishon's Transmission Den / Bushing or Needle Bearing
« on: December 31, 2020, 07:34:12 AM »
For you long glide users, do you use a bushing or needle bearing in your tailshaft in a FED? Just wondering the do's and dont's. Thanks...

11
Front Engine Dragsters / Re: new to the page
« on: July 23, 2020, 08:52:37 PM »
Neil and Parks is now offering people to come to their shop and build chassis. You weld so that might be a great deal. Call them, they are great guys and can help with anything.
Greg S.

12
Front Engine Dragsters / Re: new to the page
« on: July 21, 2020, 03:58:01 PM »
Welcome Greg, decide how fast you want to go and order the correct SFI book from NHRA. All the information you need to build a chassis right.
Good to see another Greg on here...
Greg S.

13
Wanted to buy / Re: wtb for 9" axles
« on: June 18, 2020, 11:06:27 PM »
Still have a new set of strange 31 spline out of my fed. Will try to get pics posted.

14
Front Engine Dragsters / Re: Tire ShAkE
« on: June 18, 2020, 11:04:23 PM »
What air pressure?

15
Dan Dishon's Transmission Den / Re: Power glide pumping fluid from vent
« on: January 18, 2020, 11:01:09 PM »
I just saw the gasket and helped put it back in and check it. I will post a pic of the gasket. Oh and it did not leak a drop this time...

Pages: [1] 2 3 ... 14