Messages

721

Roo Man's Room / Re: Mopar 8 3/4 "

« on: December 26, 2013, 07:50:23 PM »

I looked though my log book and found my best pass in this car 3.55 gears 31" tires
60ft 1.119
330ft 2.978
660ft 4.545
660mph 156.92
1000ft 5.914
1320ft 7.109
1320mph 186.02
This car typically tripped the 60' with the rear tires. I also found 1.08 60's

722

Roo Man's Room / Re: Mopar 8 3/4 "

« on: December 25, 2013, 09:49:08 AM »

Oh yes but once we built a new chassis we did install a 9"

723

Roo Man's Room / Re: Mopar 8 3/4 "

« on: December 25, 2013, 09:47:56 AM »

We ran hundreds of passes in our 1600 lb fed with a blown SBC running 7.40's this was with Richmond street gears

724

Roo Man's Room / Re: Clutch Pedal

« on: December 22, 2013, 08:14:11 PM »

Looking at the pics of pedals I am trying to figure out the geometry needed

725

Your Builds / Photo Gallery / Re: The latest car out of my shop

« on: December 22, 2013, 08:10:50 PM »

You do build a great looking car!

726

Roo Man's Room / Re: starter and mag switch

« on: December 16, 2013, 06:50:42 PM »

Here is my shifter and switch locations

727

Your Builds / Photo Gallery / Re: Newrotic Racing

« on: December 12, 2013, 05:15:20 PM »

Thanks it only shook a little

728

Your Builds / Photo Gallery / Re: New Car Build 205"

« on: December 09, 2013, 06:47:50 PM »

Car looks great!

729

Your Builds / Photo Gallery / Re: Newrotic Racing

« on: December 09, 2013, 05:08:28 PM »

A little wind

730

Your Builds / Photo Gallery / Newrotic Racing

« on: December 09, 2013, 12:21:38 PM »

Here is a one of my qualifying passes last season at Woodburn Dragstrip this was a  6.62 at 210

731

Roo Man's Room / Re: Clutch Pedal

« on: December 01, 2013, 11:43:10 AM »

I appreciate the replies, I assumed a bushed pedal would work for my combination.

732

Roo Man's Room / Clutch Pedal

« on: November 29, 2013, 08:31:39 PM »

Looking into adding the clutch pedal on my dragster and am wondering if a bushed pedal is what I should use or do I need to go with the style like McKinney sales with Torrington bearings to take out all of the unneeded slack?

733

Roo Man's Room / Re: Transmission Tunnel

« on: October 22, 2013, 07:15:57 PM »

My last car I built not my current car I built a transmission tunnel to keep the fire suit to a minimum. Engine was out 39"

734

Wanted to sell / Crower 10.7" 3disk hemi

« on: September 20, 2013, 08:20:16 PM »

I have a Crower 10.7" 3disk hemi pedal clutch with 3 sets of brand new floaters and disks

$2200.00

735

Your Builds / Photo Gallery / Re: New member 200" Supercat FED

« on: July 08, 2013, 09:03:29 PM »

john,
I still say the nailhead belongs in an older chassis. 
john

Very cool but yes it would look real bad ass in a 140" chassis!