Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - skydvrbob

Pages: [1]
1
Roo Man's Room / SFI specs
« on: February 27, 2024, 03:48:48 AM »
I've got the 2.4D specs for 6.00 and slower. But not the 2.6C. Is the top shoulder rail (item #3) The same for 6.00 and 7.50? I looked at an older car and it is 1.375".

2
Wanted to buy / steering box
« on: February 07, 2023, 03:20:14 AM »
Would like to by a strange box. Or something similar.

3
Front Engine Dragsters / Back to the track
« on: November 11, 2020, 10:30:39 AM »
Took the car out to Piedmont last sunday. Finally it's running right. Nice day, Ran 5.27  then added 20 percent and ended up with a 4.97.  Not to bad for a low dollar 350. Hopefully the weather will clear up for another weekend run sometime this year.

4
Wanted to buy / WTB -20 firesuit
« on: July 29, 2019, 04:01:59 PM »
Looking for a -20 suit. Two piece. I'm 5'10" 170 lbs. Long legs.

5
Wanted to sell / chaparral trailer
« on: September 14, 2018, 10:13:54 AM »
1982 chapparal. 42' New 14 ply tires, all new bearings, all new springs and hangars. Lower pockets are ok. Some surface rust on frame underneath. A couple of spots on outside by generator door. AC works, lights work. Inside has been sandblasted and epoxy painted. $9800 I'm in NC

6
Spud Miller's Cave / high speed to lean
« on: September 28, 2017, 05:15:06 AM »
I ran the car the other day and it worked great down low but leaned out and nosed over on top. Is there a simple way to keep it lean coming out then richen it up on top. Hilborn stack with only an idle bypass. No high speed.

7
Front Engine Dragsters / lebanon valley
« on: August 30, 2017, 04:49:12 AM »
Is anyone from here going to the nostalgia meet in Lebanon valley,NY in a couple of weeks?

8
Wanted to sell / strange 12 bolt
« on: August 03, 2017, 05:28:58 AM »
I have 2 strange aluminum 12 bolt drop outs for a 9 inch case. one used 3.25 bearings the other 3.06. The 3.25 has an aluminium spool,with bearings.  Make offers. I have a few ring and pinions as well as nodular centers but they are 3.06 bearing dia..

9
Dan Dishon's Transmission Den / case weight
« on: March 27, 2017, 04:57:35 AM »
Who makes the lightest powerglide case that is SFI approved?  Reid,JW, Etc.

10
Wanted to buy / 35 spline aluminum spool
« on: November 30, 2015, 06:09:33 AM »
Looking for a used 35 spline 9 inch spool. Aluminum.

11
Wanted to sell / FED trailer
« on: November 19, 2015, 05:19:54 AM »
Fits a 185" fine. Will fit 195 but a 200 would be close. 57" wide inside. Shelf in front over wheels. New tires. Has brakes. $2500 obo.Cell is 3368470301 It's in NC

12
Wanted to buy / WTT for FED
« on: August 11, 2015, 01:04:59 PM »
I have a clean 2006 GTO with 46k miles. 6 speed and black interior. 2000 miles on Michelins and koni shocks. No hot rod mods. Would like to trade for a 185" + FED. I'm in NC

Pages: [1]