Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - fuel749

Pages: [1]
1
Wanted to sell / BBC tunnel ram injection
« on: December 27, 2021, 10:55:16 AM »
Short deck BBC tunnel ram injection.  Set up for alcohol.  Bug catcher on a Holley Pro Dominator intake. Includes pump (not shown, it's on its way back from getting flowed) and belt drive.  Text 603-234-9496 for pics

2
Wanted to sell / Chassis jig
« on: March 01, 2020, 06:32:49 AM »
Chassis table with jigs and fixturing to build  FED's, altereds and RED's.  Modular in design the main table is 13' long by 36" wide and weighs over 1000 pounds.  It features 40 numbered holes down the outer rails for the included tooling.  With the included extensions I've built cars to 270".  This table could easily be used to build door cars if you wanted to make some tooling for it.  Machined flat top surface. Also comes with setup notes and whatever little tools and gizmos I've made for it over the years.  Formerly the chassis Dragster Supply/David Beard race cars chassis table.  Pics to come.  $5500.00. This table could be set up and building cars whithin a couple hours of getting it home.  Call or text David @603-234-9496

3
Wanted to sell / Hilborn fuel injection
« on: June 26, 2019, 04:15:21 PM »
Complete Hilborn stack injection for SBC.  Manifold, pump, timing cover.   Flowed and set up by Spud a few years ago, Shafts and butterflies were replaced at the same time.  Bolt it on and go.   $1800.00  Call or text David 603-234-9496 for pictures. Credit cards accepted

4
Wanted to sell / Bantam Altered
« on: October 28, 2018, 08:03:42 AM »
4130 chassis built to look old school with square and stepped lower rail.  New in 2013.  Certs to 7.50, cert current through 2019.  Built by David Beard Race Cars/ Dragster Supply.  Winner 2015 New England Hot Rod Reunion 9.0 class.  8 3/4 Chrysler with Strange brakes.  Early Ford front end with Halibrand wheels. Fits large driver.  Weighs 1600 with 230 pound driver.  Best of 8.79 with stack injected SBC on alcohol.  Roller $8500   Call or text David at 603-234-9496

5
Matt Shaff's Engine Shop / cam specs
« on: March 13, 2018, 09:43:59 AM »
Looking for input on cam selection for a stack injected SBC on alcohol. Anybody have any input on things like lobe separation angle, duration etc....

6
Wanted to sell / Bantam Altered
« on: October 19, 2017, 08:34:43 AM »
Bantam Altered for sale. Built in 2013 by David Beard/Dragster Supply. Certs to 7.50, fits large driver. 355 SBC steel crank,Scat rods, 13 to 1 pistons. Patriot performance aluminum heads. Hilborn injector on alcohol. Fresh by Spud 3 seasons ago. 8 3/4 Chryslers rear with Moser axles and spool. PG trans with Ultrabell and DJ blanket. Best of 8.87. Winner 2015 New England Hot Rod Reunion 9.0 class.  All certs current. Selling as a complete setup including 16 foot trailer with generator and any fuel/oil left. Will separate.

Complete operation $18000.00. Call David with any questions 800-481-1957

7
Wanted to sell / 178" FED
« on: November 04, 2015, 05:50:03 AM »
Brand new 175" chassis by Dragster Supply. 21" shoulder hoop, fits 6 foot 220 pond driver, SBC motor plates, seat, steering box with all linkage, front axle with spindles, tie rod and radius rods, chassis fully welded. This is the stage 2 kit that normally sells for $5495.00, yours for $3995.00. Call David 800-481-1957

8
Wanted to sell / spoke wheels
« on: September 02, 2015, 06:45:34 AM »
If anybody's looking for some nice spoke front wheels, Dragster Supply .com is having a sale. I've got a set, nice stuff!

9
Spud Miller's Cave / optimum fuel pressure
« on: January 22, 2015, 07:04:26 AM »
Is there an optimum fuel pressure to shoot for with my Hilborn pump? Is cavitation or something similar an issue at higher fuel pressures? Any benefit from a gear pump with more pressure? All of this is on Alky by the way.

Pages: [1]