Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - captndiet

Pages: [1] 2 3
1
Spud Miller's Cave / Re: Enderle Pump I.D. help
« on: December 22, 2020, 08:57:28 AM »
Found the info.

If not stamped it is a 80A-1

Jeff

2
Spud Miller's Cave / Enderle Pump I.D. help
« on: December 21, 2020, 02:20:22 PM »
I was looking for something in my collection the other day and came across a new Enderle 80A I had stashed.

Problem is no paperwork and it is not stamped with a size.

Can anyone tell me what the idler gear width is on a 80A-1 so I can determine the size of this one?

Mine measures .601" wide.

Thanks!

Jeff

3
Front Engine Dragsters / Re: FED front spindles
« on: March 23, 2018, 05:46:02 AM »
Justin is correct.

7.5 degree and 8 degree are the two common kingpin inclinations.

I believe Strange is 7.5 degree and everyone else is 8 degree.

Jeff

4
Wanted to buy / Re: WTB/ Period correct Rear end
« on: March 01, 2018, 10:47:28 AM »
The Ford Banjo can be upgraded to 28 spline axles as used in the 9" Ford.

Also a 9" Ford mini spool can be modified to fit in the Banjo carrier.

Hot Rod Works in Idaho can fix you up.

But you are still limited to Cackle Car status.

Jeff

5
Jon's Wheel House / Lightweight Wheels
« on: February 27, 2018, 04:22:10 PM »
Guys

What are the lightest front and rear wheels?

17x2.25" fronts and either 15"x10" or 15"x12" rears.

New or Old.

Jeff

6
Spud Miller's Cave / Re: FIE Rev-Limit Relay
« on: January 25, 2018, 02:36:38 PM »
Got it!!

Thanks for the quick reply.

Jeff

7
Spud Miller's Cave / FIE Rev-Limit Relay
« on: January 25, 2018, 12:03:39 PM »
Spud

You may have addressed this before, and if so, forgive me.

Can your Rev-Limit relay as you have it wired in the attached .jpg, be used as a two-step?

If you wired the 12v supply to both the Rev-Limit relay and the MSD 8950 thru either a separate button switch or your trans-brake button, wouldn't it act as a two step?

Jeff

8
Roo Man's Room / Re: Engine Placement in Altered/Funny Car Chassis
« on: January 15, 2018, 05:18:44 AM »
Roo

Thanks agin for your advice.

Jeff

9
Roo Man's Room / Re: Engine Placement in Altered/Funny Car Chassis
« on: January 12, 2018, 05:19:57 PM »
O.K. Roo, one more.....

Lets use the Mark Williams print as a referance...

The rear axle centerline is called out as 15" above ground level with a 33" tire with 3 1/2" ground clearance on the frame.

If you run a 33" M/T tire or equivalant all is good.

If you run a Goodyear D2585, 31x12x15 tire, they actually grow more than a 33" M/T, but setting there are about 31".

What would you set the rear axle centerline at?

Thanks!

Jeff







10
Roo Man's Room / Re: Engine Placement in Altered/Funny Car Chassis
« on: January 10, 2018, 06:06:01 PM »
Roo

Thanks for the input.

I will probably follow your advice.

Jeff

11
Roo Man's Room / Re: Engine Placement in Altered/Funny Car Chassis
« on: January 09, 2018, 05:57:17 PM »
Roo

Initially just a small cubic inch injected alky/auto trans deal.

500-600 hp.

1700 lb.

Solid front & rear suspension.

125" w.b.

1/8 mile car.

Jeff

12
Roo Man's Room / Engine Placement in Altered/Funny Car Chassis
« on: January 09, 2018, 08:55:59 AM »
How far out and what crankshaft angle/ground clearance are typical for the average altered chassis.

I know many Alky cars have the engine out 67"+ but not sure what crank centerline is, up, zero or down.

The Mark Williams F/C print has the engine out 63" and the centerline at the front of the crank is 10 1/4" from the ground, which would be down in the front. Chassis ground clearance is 3 1/2".

The S&W altered print has the engine out 62 1/4" and centerline at the front of the crank is 13 5/16" from the ground which would be zero. Frame ground clearance is 4 1/2".

Any input is appreciated.

Jeff

13
Spud Miller's Cave / Re: Q.D. coupler used for Primer Bottle
« on: May 27, 2017, 11:10:14 AM »
Thanks for the info Spud.

That was what I needed.

Jeff

14
Spud Miller's Cave / Q.D. coupler used for Primer Bottle
« on: May 25, 2017, 06:25:42 AM »
On injected fuel motors, many use a bottle or box to start the engine on Alky then switch over to fuel once warm.

What quick disconnect coupler do they use between the bottle and the distribution block?

Brand and/or size?

See attached borrowed photo.

Jeff

15
Spud Miller's Cave / Re: Port Nozzle Design
« on: March 24, 2017, 06:21:21 PM »
A normal aspirated nozzle holder would have the hole outside the the hat or port.

These would be pulling the air from inside the hat or port.

Jeff

Pages: [1] 2 3