Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - tdietz

Pages: [1] 2 3
1
1969 Logghe Chassis. 200" Set-up for Big Block Chevy + Glide. Cage is 19" but will accommodate a driver around 5'11" - 225 lbs with out issue. 8 3/4 with 390 gears. New Zoomie Headers. New Fuel Tank. New Master Cylinder. Current NHRA Certification. Selling to finish other projects and health reasons.

As sits $8,000

Can send many more pictures via email or text.

Contact Tim (717)524-8432 via Text or Phone. Please leave a message as I don't always get to my phone

2
Wanted to sell / 27 Ford Roadster
« on: October 02, 2016, 04:41:41 PM »
27 Ford Roadster minus engine and trans. Chromoly, ladder bar car. Has front brakes, 4.11 rear gears in a 9" ford rear. Larger cage. 7al3 msd ignition box. Certified NHRA in 2015 and IHRA in 2016. Belts new in 2015. Includes headers and engine plates for small block and big block Chevy. Currently was run with a big block and has run 5.19-1/8 mile and 8.46-1/4 mile.

Will trade for front engine dragster
Asking $10,500

Contact
Tim Dietz
(717)524-8432

3
Spud Miller's Cave / Re: Flat under low end Load
« on: May 27, 2015, 08:30:05 AM »
Thanks everyone for the help.  We ended up changing to the Digital 6AL box, and put a new cap and rotor in it.  And cleaned the problem right up.  No more issues....Thanks again for the help!

4
Wanted to sell / 175" WB FED with All Aluminum SBC
« on: May 27, 2015, 08:28:26 AM »
2012 175" wb Mark Williams Kit Front Engine Dragster. Ford 9" Rear with 4.11 gears, Mark Williams Axles, Hoosier 32/14-15 tires (New last year), Solid Front Axle. Trans-Specialties Powerglide Transmission and torque converter with less than 50 passes on both.

All Aluminum 410ci small block Chevy. Rodeck block, Brodix -12 heads fully ported, Lunati crank, Oliver Rods, JE Pistons, T&D Shaft Rockers, Wolff 4 Stage Dry Sump System, KSE Front Cover with mechanical water pump. Kinsler 2 5/8 Injection with Down Nozzle (nozzles ported in heads), Kinsler mechanical fuel pump.

Car runs consistent 8.0's @ 166 and will dip into the 7.8's with the right conditions.

Contact Tim (717)965-7187 or dietzd140@gmail.com Located in Hanover, PA

Asking $25,000 or willing to trade for Big Block Chevy or 7.90/8.90 Jr. Dragsters

5
Spud Miller's Cave / Re: Flat under low end Load
« on: May 19, 2015, 10:14:46 AM »
All, thanks again.  I did change out the ignition box, new cap and rotor went over all my grounds, and checked all my connections.  I did find a loose wire from my distributor to my box, but that wire I would think would either give me spark or no spark at all.  We will be racing this weekend.  I'll keep everyone up on if it worked or not.

Thanks again!

6
Spud Miller's Cave / Re: Flat under low end Load
« on: May 12, 2015, 03:42:43 AM »
All thanks for giving me some stuff to check.  Going to begin looking through everything tonight.  Hopefully it's something really noticeable that we just missed at the track!  (but it never is!  LOL)

7
Spud Miller's Cave / Re: Flat under low end Load
« on: May 11, 2015, 12:25:52 PM »
Bill we are getting 12 volts at least while it's running.  I've checked this before.  We charge the battery after every run.  I'm going to check rotor phasing later this week and pick-up wires.  I'm almost positive the wires are right but will make sure.  I was thinking of eliminating the starter saver just to get that out of the system all together.  We run a high torque starter and I feel it would start the same without it.

8
Spud Miller's Cave / Re: Flat under low end Load
« on: May 11, 2015, 10:56:08 AM »
I can take the 2-step out of the equation.  I also thought the same thing about checking the rotor phasing.  I'll see what I can come up with.  Really want this thing right before Memorial Day.....

9
Spud Miller's Cave / Re: Flat under low end Load
« on: May 11, 2015, 09:31:33 AM »
That's all great and I understand you are probably correct.  BUT, I didn't have issue last year and I don't have 600-800 for a Mag.  I'm sorta stuck at this point with what I got.  I can't afford to just dump all of it and go to a MAG. 

For the previous 2 years we've had no issues.  It developed late last year and we attributed it to weather.  But, now I'm almost certain it is ignition related.

10
Spud Miller's Cave / Flat under low end Load
« on: May 11, 2015, 04:49:50 AM »
Ok guys, 175" WB FED, 410 SBC timing around 36 degrees, MSD Pro-Billet Dist, MSD Blaster 2 coil, MSD 6 ignition box, MSD starter saver, and MSD 2 step rev control.  Engine is fuel injected on Alcohol (down nozzles), Kinsler 450 mechanical pump.

The car on launch runs flat and breaks up.  Our first pass of the day our 60' times were 1.415ish and our normal 60' times are roughly 1.16ish.  It is flat then all of a sudden will pick up and our MPH on top end is normal 166MPH.

We tried leaning the barrel valve, then we tried richening the barrel valve, nothing made a difference.  And by the end of the day the engine would clean out until I hit high gear (powerglide) and then it would break up again. 

I'm pretty certain this is ignition, but where or what part of the ignition should I be looking at?  Our tach is the digital shift light with the tach built in, and it seems very erratic as well....

11
Wanted to sell / 50cc moped/pit vehicle
« on: April 23, 2015, 09:28:42 AM »
1972 Garelli, completely redone.  runs like a top.  Perfect for cruising the pits at all the races.  We use one now to tow a Jr. Dragster around.

asking $450.

Contact Tim
(717)965-7187

located in South Central Pennsylvania

12
Spud Miller's Cave / Re: 18V Battery to run Distributor?
« on: November 10, 2014, 09:04:47 AM »
LOL!  awesome help guys!  I was sort of figuring this but wanted to be sure.  I appreciate the help!

13
Spud Miller's Cave / Re: 18V Battery to run Distributor?
« on: November 10, 2014, 08:03:16 AM »
Spud, thanks.

By 24V I'm assuming your saying using a 24Volt battery?

Thanks.

14
Spud Miller's Cave / 18V Battery to run Distributor?
« on: November 10, 2014, 03:52:50 AM »
I see Neil and Parks offers an 18V battery that is used instead of a larger automotive style battery.  On our car this would be powering our tach light, transbrake and the biggie, our msd distributor.  My question is, will the 18V battery work with a msd Distributor?

Thanks for the help.

15
Wanted to sell / 11 FT MORSE CABLE
« on: January 15, 2014, 08:36:41 AM »
Looking to trade an 11 ft morse cable for an 8 ft cable.  will sell if need be but really wanted to trade.

Call email or text.

Tim

tim@timdietzracing.com or (717)965-7187

Pages: [1] 2 3