Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Scuzme

Pages: [1]
1
Spud Miller's Cave / Re: Offset Drive
« on: July 07, 2018, 11:33:30 PM »
It does have a clamp as can be seen in the background. I think the easiest way would be to make a new shaft for the offset drive and mount the chopper and square drive on that. I will give Spud a ring tho just to make sure there is nothing available first. Thanks anyway.

2
Spud Miller's Cave / Re: Offset Drive
« on: July 07, 2018, 09:36:43 PM »
Hi Paul, these pics might help to see my problem.

3
Spud Miller's Cave / Offset Drive
« on: July 07, 2018, 06:03:44 PM »
Hi there, I am fitting an 8/71 Blower to our sbc. I need to use an offset drive for the Mag. The mag we are running is an MSD promag lt12. I was thinking along the lines of a 3” Dunn. The problem is they have a cross drive and the Mag has a square drive with a magnetic chopper below it. Does anyone know if there are adaptors available or any other ways of adapting the mag to the drive.[/url]][url][/url]

4
Dan Dishon's Transmission Den / Re: Powerglide cooler bypass valve
« on: February 27, 2017, 10:12:13 PM »
Hey thanks Guys for all your info. I will rebuild the Trans and run it and get some baseline temps and pressures and see how we go.

   Cheers and thanks for your help.

5
Dan Dishon's Transmission Den / Re: Powerglide cooler bypass valve
« on: February 26, 2017, 11:14:14 PM »
Hi Bikeguy, thanks for your reply. Yes it was a standard case. We can't run a cooler with fan as we don't have the battery capacity for that. I do think your right about an external means of cooling the oil between rounds but I also think it needs to be circulated through the torque converter from the pan, but that's a bit further down the track. I need to get some pressures and temps first.
     As far as the cooler pressures go, I have been told that is not too high for a good cooler to handle. I don't know, maybe someone can tell us. I have attached a pic of the mistress ha ha that's the cars name.

   Thanks to you all for looking and answering my questions.

6
Dan Dishon's Transmission Den / Re: Powerglide cooler bypass valve
« on: February 26, 2017, 04:22:08 PM »
The transmission was bought as a new unit from a reputable builder. It is running a pro transbrake.
From the outset it seemed to be running fine and doing everything it was meant to do. Backing up, select reverse and and hold brake button in, no problems until recently when we found we could back up without holding button in. The last pass we made without using the brake and all was well until going through the 1/4 and she stepped sideways a little. the cause of this was that the band had pushed so hard on the band adjusting bolt that it pushed it through the side of the glide case. I cant tell why or what had caused it but it maybe excessive heat build up or a fault with the valve body. The result is that I am rebuilding the box with new clutch plates and fitting a new transbreak valve body, but I would like to sort out the temp problem as well.

7
Dan Dishon's Transmission Den / Powerglide cooler bypass valve
« on: February 25, 2017, 10:15:32 PM »
Hi Guys, I'm a newbi here so first off I had better introduce myself. I am Crew chief for my Brother who runs a new Fed built to Junior Fuel regs. We basically built it because we liked the nostalgia side of things. So far we have only made around 8 passes with the last resulting in a busted transmission.
       You guys have a wealth of information here that I would love to tap into so here goes my first question.
Has anyone tried to block off the cooler bypass valve in the pump to make the cooler a full flow unit instead of just running on bypass oil. I have looked at the schematics for the Glide and I can't see why it can't be done but maybe I am missing something. 
   Looking forward to your replys.

Pages: [1]