FrontEngineDragsters.Org Forum
Technical => Roo Man's Room => Topic started by: Paul New on October 01, 2015, 05:42:41 AM
-
Going to be cutting the front half off of the car soon as after last weekend it is a little bent up. I know I will be needing to have a custom front axle bent as my old front axle was a narrowed MW that I made into a 2-piece and I want a one piece axle. The axle is not the reason the crash happened but I didn't like the way it performed it flexed at the spice point. Just looking for ideas on uprights and diagonal supports to keep the frame from flexing. (http://images.tapatalk-cdn.com/15/10/01/00a65eceb11f690f982a15f0333bc88e.jpg)
Sent from my iPhone using Tapatalk
-
no problem
-
I was planning on getting ahold of you Bruce
-
I went for a drive today to Boise and was able to check out a really nice car
I was told Roo built this one
(http://images.tapatalk-cdn.com/15/10/02/2da9effce25fca2d8754cd51d5d07199.jpg)
Here is a Parks car that has the diagonal going the opposite direction that looks like a slip joint? I saw this one at our June race
(http://images.tapatalk-cdn.com/15/10/02/417bc5a16c38149c636a064bccfe7f9f.jpg)
Sent from my iPhone using Tapatalk
-
Paul,
yep, Kenny's is one of mine. Originally built for Jimmy Gravitt out of Illinois some time ago. My newer cars have the rails sleeved at the uprights and generally the motor is a little further out.
The N & P car is also a little older as it is their earlier high seat design.
Roo
-
I do like the clean look of your chassis very sanitary! I am going to start cutting my front half off soon, going to maintain my 200" WB and engine position out 42"
-
Finally started the project today gutted it and cut it in half
Sent from my iPhone using Tapatalk
-
Finally worked on it again today decided to cut out the rear end upright and move some things around a little since I am this far what the heck
Sent from my iPhone using Tapatalk
-
Did a little work this weekend with my dad and brother
Sent from my iPhone using Tapatalk
-
A couple more
Sent from my iPhone using Tapatalk
-
Very nice Paul. Your Christmas present. ;)
-
Did a little work this weekend with my dad and brother
That's high quality time for me!
-
There needs to be a thumbs up...Nice
-
Thank you! We do 98% of our race work as a family when we go to the track its 100% family time dad, mom, brother, wife, and kids.
-
👍👍👍👍👍👍
-
Looks good, I am currently rebuilding the front half of my car also, and funny enough my dad and brother (brother also the driver) were here to help this weekend. I love em, but I get more done by myself.
-
We actually work well together!
-
Gentlemen you are so blessed to have family involvement. My Dad and 4 brothers have noticed very little of my drag racing projects over the years (40+). George
-
if you get along while working then congradualtoin's.Been working with my father for 32 years and its been 31 years of debating and arguing.Has gotten better as he has gotten older and realized out of 3 kids I'm only one that takes care of anyone in family with problem. Or maybe he has just figured xxxx he is going to do it his way any how,might as well not argue with him.Him being me of coarse.LOL
-
Built the front nose cone weight bar area today(http://images.tapatalk-cdn.com/16/01/10/807379bd43d130b704bb4c6e2b104f70.jpg)(http://images.tapatalk-cdn.com/16/01/10/ecc880262fb30d20805505ca86b6bcca.jpg)
Sent from my iPhone using Tapatalk
-
My engine bay is a little different than most as my car is a little narrow with the drysump pump mounted low so this is what I ended up doing.(http://uploads.tapatalk-cdn.com/20160125/8dc26d8006283124497c740f0a4f06d2.jpg)(http://uploads.tapatalk-cdn.com/20160125/973643d9d311ac255802bd0f7f533e9f.jpg)(http://uploads.tapatalk-cdn.com/20160125/a21bda929b91cdd72a6f3de0904b02ff.jpg)(http://uploads.tapatalk-cdn.com/20160125/8b105ee368728e777d6486fefea6d447.jpg)
Sent from my iPhone using Tapatalk
-
Hello Paul:
Did you purchase the front axle or make it?
I'm looking for one that's less than 39" that's on my FED.
Thanks: Matt
-
Matt I bought it from the Chassis shopthis is the one I bought
https://secure.chassisshop.com/partdetail/C42-438/
-
Thanks Paul:
I enjoy following your progress on this site and Facebook.
I'm going to be working on mine soon and will try to post pictures.
-
Thanks Matt appreciate it.
-
Well I contacted the Chassis Shop for a front axle.
They are not in production at this time and none in the near future.
Mark Williams and S&W race cars only sell wide ones.
I really like the look of the narrow front end but am wondering who to call now.
If anybody knows who to call let me know.
My needs are pretty common. 6" drop with SPE spindles.
Matt Shaff
-
Well I contacted the Chassis Shop for a front axle.
They are not in production at this time and none in the near future.
Mark Williams and S&W race cars only sell wide ones.
I really like the look of the narrow front end but am wondering who to call now.
If anybody knows who to call let me know.
My needs are pretty common. 6" drop with SPE spindles.
Matt Shaff
SW should be able to build a short axle for you as its what they offer in there FED chassis kit.... they built me one a few yrs ago...
-
Matt one more suggestion, heres internet links to new 4130 CM 0.120 wall, 1.50 outside dia. axles, 36 or 39 wide, 6 drop with SPE bosses, priced at $178.99. Years ago for my dragster, I selected a MW Enterprises, Inc. axle and it was top quality. No experience with Pro-Werks front axle but I have bought from Pro-Werks before and was pleased with item. Alan
http://www.pro-werks.com/partdetail/C42-438/
http://www.pro-werks.com/partdetail/C42-437/
-
Matt one more suggestion, heres internet links to new 4130 CM 0.120 wall, 1.50 outside dia. axles, 36 or 39 wide, 6 drop with SPE bosses, priced at $178.99. Years ago for my dragster, I selected a MW Enterprises, Inc. axle and it was top quality. No experience with Pro-Werks front axle but I have bought from Pro-Werks before and was pleased with item. Alan
http://www.pro-werks.com/partdetail/C42-438/
http://www.pro-werks.com/partdetail/C42-437/
Pro werks is the chassis shop the last few times I have tried to buy moly tubing from them they were out and unsure when they would have any in stock....... I would call Neil Parks I have a really wide front axle for sale with a Mark Williams torsion bar c-c of king pin boss is 45
-
Bruce Dyda did mine, very nice piece and easy to deal with. Great guy.
-
Ever try Rooman? He does support this forum.