Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - 225digger

Pages: [1] 2 3 ... 11
1
Front Engine Dragsters / Re: 5.7 Hemi???
« on: May 10, 2022, 05:11:11 AM »
im not up to par on the modern stuff as far as cost like piecing one together vs buying a drop out, but a hellcat drop out would be neat, just did a quick browse on ebay and you can get a drop out for around 15k. with supercharger... id think with some tuning they could make a good bit more power reliably ?

i have a gen 1 392  and glad i have all the parts for it before covid hit.  im sure i have 25k+ into it  with all the goodies... aluminum rods, nitro pistons, aluminum rockers etc....  and thats still using iron block, heads, and a 65 yr old crank..... its for a cackle car though.

my FED i have on the back burner i have a 496 im putting into it,  put often look at ls stuff, then i get confused with all the interchange stuff so i just revert to old school

2
Tow Vehicles / Re: Dynastar trailer, new trucks and other questions.
« on: April 15, 2022, 09:05:06 AM »
BW has a taller ball and off set that might help if you have a turn over ball.




3
Matt Shaff's Engine Shop / Re: Zoomies vs collector headers
« on: March 25, 2022, 08:41:42 AM »
if you get them hot and then paint it will last alot longer,  i did several sets like that both with the black and silver vht

they also do this with ceramic coatings, you need to pre heat to 1200 degs, then let cool and paint. it burns off all the oils and stuff

4
Front Engine Dragsters / Re: Air Scoop - Production or Homemade?
« on: March 15, 2022, 12:15:09 PM »
there used to be a guy on ebay selling them in fiberglass

https://ariascomponents.com/product-category/scoops/


5
Spud Miller's Cave / Re: where to buy nitro other than Sunoco
« on: March 15, 2022, 10:12:20 AM »
torco race fuels used to sell it by the gallon, and i think alky digger sold it for a bit...... torcos site has race fuels and nitro is NA


they use nitro for fertilizer ?  most likely why its going up

6
Spud Miller's Cave / Re: where to buy nitro other than Sunoco
« on: March 14, 2022, 12:16:17 PM »
if you find out a price make sure to post,  im a long ways off on my cackle car project, but might need to order a drum before it gets to high or obsolete

7
Spud Miller's Cave / Re: where to buy nitro other than Sunoco
« on: March 14, 2022, 10:53:04 AM »
i have never looked into it,  but  schumacher sells it, worth a look    https://dsr.parts/pages/nitromethane-sales

8
Spud Miller's Cave / Re: Injection Alky Vs. Carb Gas
« on: March 09, 2022, 01:39:14 PM »
you need to build what you want, thats a big part of bracket racing, you can race what you want and just change a dial.... race for fun till you get it figured out.....   the FED i have will get a 496 bbc  with a bird on a tunnel ram.

9
Spud Miller's Cave / Re: Injection Alky Vs. Carb Gas
« on: March 09, 2022, 05:27:27 AM »
if your going for functionality over looks.   alky carb is a great setup.    i ran a very basic system yrs ago that was very consistent,  350 sbc with iron eagle heads, like 11.1 comp solid flat tappet.

it had a 750 bg alky carb on it, with a BG barrel valve to control fuel pressure, used a edelbrock high flow mechanical pump, 3 gal tank in front of radiator, it was very simple and maintence free, after the car was loaded up i would open the fuel lines, just cracked them to drain back in the cell.... drain the bowls and spray in wd40, if i knew it would sit for a longer period i would spray lube in the hoses and cap the fuel cell so air could not get into it. i had a hose going from the intake under carb to inside car with a barrel valve on it, i would open that up to lean out the motor to build heat faster..... it was a good setup, ran 10;60s in a 68 camaro


10
Front Engine Dragsters / Re: bracket racing a FED
« on: February 15, 2022, 06:34:24 AM »
imo, keep it simple, a mild sbc on gas, just use the belt driven water pump with a 160 thermostat.

this way water is always moving through the radiator,  put an electric fan on it and turn on and off as needed.

that honda radiator might work only way to find out is to give it a try, i only ended up with the civic radiator as yrs ago on the forums that was recommended to me to use.

11
Front Engine Dragsters / Re: bracket racing a FED
« on: February 13, 2022, 11:15:24 AM »
Thanks for the replies.

225DIGGER....do you happen to know the dimensions of the Civic radiators? More often than not, parts on Ebay don't have a great deal of info like dimensions, and I can understand that wouldn't be important if I were looking for a radiator for a Civic. $100 with a fan would be sweet!

Lynn

so the one i have is 14.5 wide and roughly 18" long  i wish i had a part number for you but i bought this thing like 15 yrs ago for my project.  yeah that long ago im that guy who has alot of projects that seem to never get finished.

12
Front Engine Dragsters / Re: bracket racing a FED
« on: February 12, 2022, 10:22:49 AM »
look on ebay for a honda civic aluminum radiator, you can get them for under 100.00 with fan, new.... they are small enough to fit between the rails but not to small.  i have no experience in actual use, but its what i have for my dragster project.

13
Front Engine Dragsters / Re: Nostalgia BBC Recipe
« on: December 24, 2020, 08:11:07 PM »
i think the link below is what your seeking ???

https://www.draglist.com/stories/SOD%20Apr%202001/SOD-042701.htm



.

14
Front Engine Dragsters / Re: SPE steering box rebuild
« on: November 01, 2020, 06:03:28 AM »
sell it on a FB group, someone will pick it up for 200 for there cackle car project..... then your half way there to a new strange box.

15
Roo Man's Room / Re: 140-160" FED Build
« on: July 23, 2020, 09:25:47 AM »
i posted in the other thread but here. its 200"....shorten it to how you want

https://swracecars.com/product/blue-print-200-front-eng-dragster/

Pages: [1] 2 3 ... 11