Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Mike Lawless

Pages: [1]
1
Front Engine Dragsters / Re: Seeking FED Wisdom
« on: March 18, 2019, 10:16:09 AM »
I know that car. It should come with caution tape around it because it's dangerous (to the competition).  ;D

Hey Gino! We've met a few times. I saw that you were a member here and thought "What'dya know. Some old friends frequent this place!"


2
Front Engine Dragsters / Re: Seeking FED Wisdom
« on: March 17, 2019, 03:39:00 PM »
more boost always good,well unless you run over crank.  Little off subject. I would gear your whole deal towards ultra low weight. Like keep as short as you think will work good. 180" would be plenty long IMO.Minimum size tubing like diagonals (lower power less stress).design as many jobs into one piece as can(already fabricating it) and keep bolt sizing down to where does job but not twice size needed. I don't think you will have any problem getting it moving.

A plus is those VW guys are a loyal bunch and if its fast they go nuts over it,I have seen guys need bibs  when looking at lil brothers VW. I think thers video posted on this site of it making pass.If not there are cpl on you tube look up Bdub VW.

Words of wisdom right there.

You are correct. the VW guys are loyal. My Blue Ghia is one of the most well known "race cars" in the VW scene. Two time magazine feature car, cover of Hot VWs last year and the only VW to win at the Bakersfield March Meet in any class in the events entire history.

We've been running the car for 20 years from it's humble street car beginnings till now. Still street legal with full trim and real glass windows, weighing in at 1950lbs, it's run a best of 9.70 at 142mph at 15psi boost with it's little "bread & Butter" 2156cc motor. We'll be using this motor in the dragster. If we get the weight and gearing right, I'm fairly confident we can run NE2 without pushing the motor too hard. At least eventually!

3
Front Engine Dragsters / Re: Seeking FED Wisdom
« on: March 14, 2019, 02:45:52 PM »
As much as I hate 2 speed taxi cab transmissions I said I'd find out and it was a stock PG witj a shift kit.
Cheers

Thanks for taking the time to look it up. Mucho appreciated!

I think you can get  a 1.9_ lw for glide. Remember that you will be a lot lighter and getting it moving will not need as much push.  Low 1st ,with right rear gear,converter thats good match and super lite car I don't see how you would any problem getting it moving out of hole.

I think that what you might gain with the 3 speed you will lose because of the weight overall and the rotating weight of the internal components of both the th 350 and the 904 ! You can get a low gear set for a glide and even get away with a six cylinder carrier ! 

Most of the guys here seem to be on the same page. That does simplify things tremendously. I reckon if all else fails.....mo' boost!

Thanks guys!

4
Front Engine Dragsters / Re: Seeking FED Wisdom
« on: March 13, 2019, 09:29:56 PM »
Been awhile since I dealt with VW's,  I was at the MM this year (briefly) but hung around the T/F pits because a customer had an issue. I did do a VW RE dragster with a PG for Mike Ballard a few years ago, you can google him and see his "Scorpion" dragster

Yeah, I know that car. Bigger motor than mine at 3 liters. Mine is 2.2. He runs a procharger too. I haven't seen it run for a while, not since they were trying to sort things out.

5
Front Engine Dragsters / Re: Seeking FED Wisdom
« on: March 13, 2019, 06:40:30 PM »
I too would go with the PG. I use Coan in my six cylinders and like their customer service. Plus, they have run a K/A four cylinder Comp car so they have history with that combo. One thing I would do is put the motor plate far enough out so that if you ever want to try a 3-speed you won't have to tear up the basic chassis. ight car you'll probably want it pretty far out anyway to control wheelstands. Some Comp racers with smaller engines are using a 3-speed based on the 904 Mopar. Good luck

I appreciate the input guys. Definitely a lot to think about. A PG would be a lot easier from a build perspective. My main concern is getting it moving quickly enough on a pro tree. On my door car, I made the mistake of allowing myself to go with a higher ratio first gear than what I wanted. "The turbo needs a load," they said. Well, maybe they do if one is chasing ET and ET only. But as you all know, in index racing, it is imperative that the car reacts quickly to driver input. At any rate, some of that initial movement was lost compared to my previous NA combo. That sucker would go red on a .4 tree if I was aggressive with it. Now, the reactions are somewhere around .05 if I'm on the ball. So you can see why I'm concerned about having enough low gear. I believe the lowest first gear for a PG is 1.98?

Since the ultimate goal of this project is to win races, I need to make the right decision on this early on.

dreracecar....since your home track is Famoso in Bakersfield as mine is, if you run ANRA events or the March Meet, you may have seen my blue Karmann Ghia

6
Front Engine Dragsters / Re: Seeking FED Wisdom
« on: March 13, 2019, 09:11:25 AM »
Thanks guys.

Curly, the lower first gear was why the T350 is being considered. Not only is the low end torque a factor, but also the ability to move on a .4 pro tree. I've never had the motor dynoed to see where it makes peak torque, but based on the way I run it in my door car, I think the rpm is up there comparatively high. Maybe as high as 6000rpm.

You are right on the converter. It will be a very important decision for certain. It's been a LONG time since I raced in a car with an auto trans and converter, so I am certain the technology has changed a bunch. The early VW dragster guys had problems. But maybe there are enough small motor combos (2.2liter) out there these days that a basic formula has been figured out?

At any rate, I'm thinking that drivetrain decisions will need to be made before a single stick of tube is put in position. Tire diameter, trans housing, motor plate thickness (since we need to adapt a flex plate to the back of a VW crank AND allow for converter snout register) fore/aft motor position....not to mention how we're gonna hang a starter on it.

Makes me ask what the heck I'm getting myself into!

7
Front Engine Dragsters / Seeking FED Wisdom
« on: March 12, 2019, 05:20:06 PM »
Howdy everyone. New to the site. I've been drag racing for nearly 45 years, so I am no newcomer. I've raced door cars all that time. Recently, the time has come to hang up my driving suit, and crew for my son. We are in the research phase of building a dragster using my existing turbo charged methanol burning air cooled VW engine with the goal of running NE2. The motor is a proven performer and makes just shy of 500hp with fairly low boost (15psi). We will probably run in NE3 at first to get the kinks out, although the motor has run the door car to 9.70. So NE3 could be achievable with ridiculously low boost

We have challenges to overcome to be certain. I am a hobbyist machinist and more than capable of custom fabbing odd-ball parts, and I am an accomplished welder.

Some my initial idears make sense to me, but I may be off base. One such idear is to use a turbo 350 trans rather than a PG. The VW doesn't make the bucket load of torque than a V8 does, but enough to get a 2000lb door car into the mid 1.30 60 foot range....with a stick trans and 7000rpm launch.

So, the first question, since the build will center around the drivetrain, is a turbo 350 a hair brained idear?

Pages: [1]