Topics

1

Wanted to sell / Donovan/Enderle/Engler

« on: November 17, 2017, 07:14:16 PM »

FOR SALE:::
Engler Machine and Tool 3 piece intake with manifold adaptor to Enderle Bug/Bird.
This intake is a 2 13/16 and built for a Pro Action 14* head but will fit other raised runner heads with 5* face. Intake runners are also drilled for Enderle Nozzles on bottom side.
Comes with:
-Engler 3 piece intake with oil fill
-Engler Custom Enderle adaptor
-Engler 550 nozzles
-8 nozzle hoses
-All water lines for cylinder heads
-SCE intake gaskets (NEW)

$700.00 obo.

Donovan gear drive with pump drive for SBC. I also have a 3” pump extension available (not pictured).
$450.00 with extension.
$400.00 without.

Mallory Dual Point Distributor
Fresh with new points, cap, rotor. (spares included)
New Wires for SBC
Mallory Coil included.
$125.00

Weld 17" Pro stars (Dragster)
No bearings or caps
TF Front runners mounted

They are not perfect but usable or kept for spares
$175.00

Located in Bloomington, IN

Pics available

2

Wanted to sell / MSD Pro Mag with points box's

« on: October 20, 2017, 10:19:25 AM »

Sold

3

Wanted to sell / Weld/Goodyear

« on: April 03, 2016, 11:18:35 AM »

FOR SALE::
Weld Pro Stars
15X15
5 on 4.75
3.5 BS

GoodYear 32/14/15.
Less than 100 passes on 1700lb chassis.
$400.00

4

Wanted to sell / BRAND NEW INJECTED SBC

« on: January 29, 2016, 07:00:28 PM »

FOR SALE::
358 SBC>>>>>NEW<<<<<
Lunati Pro Series 3.520 Stroke
Manley 6.00 rods
JE Pistons 14:1
Total Seal Rings
All Clevite bearings
Comp Cams roller cam
Comp Cams lifters
Milodon Gear drive
ATI Damper
Moroso Pump/Pan
Dart Pro 1 CNC 227 runner Iron Heads.
PAC springs
Comp Cams roller rockers
Comp Cams Girdles
Enderle Stack Injection.
Enderle Pump.
Vertex Mag
Hedman Zoomies
This engine is completely new. The only used piece was the engine block. It is sitting on the stand at Freedom Racing Engines ready to go. It is perfect for a front engine dragster or small gasser

$15K

5

Wanted to sell / BRAND NEW ROOMAN FED

« on: January 29, 2016, 06:58:32 PM »

FOR SALE::
ROOMAN FED
Car is new and never ran
207" Wheelbase
22" Main Hoop
Aluminum Shorty body
New steering box
New Master Cylinder
Butler head pads
Carbon Fiber cage shroud
New Strange Fab 9.5
Plated for SBC
Fuel tank will be finished to your specs
I have a box with gauges and misc. stuff that goes with it...all new.
This car is new. It was purchased and never completed. Front wheels are not included.
$7500.00

6

Wanted to sell / Turnkey FED...just add driver.

« on: January 06, 2016, 06:32:57 PM »

This car belonged to Gene Ritchie who passed away this summer. His widow has the car for sale.
RACE READY FED FOR SALE: The car is a 1969 chassis,has a new,fresh,alum 400 chevy motor,alum heads,hilborn injection with Mag.The car is..ready to race NOW,not years down the road. It runs on 110 fuel.The car is NOT mine,but i have been ask to help sell the car which is located in Ohio. This deal includes a one yr old wedge nose trailer and 125 cc Yamaha atv to haul it around at the track.I will post some photos including the # of the guy who has it stored. Call or text Kurt. Thanks for looking.

$18,000 for car, trailer, and atv.

7

Spud Miller's Cave / Air Bleeds...

« on: August 04, 2015, 05:56:59 AM »

How important is proper air bleed flow on a Kinsler nozzle? Nozzle is a AS78-S510.

On the engine that I bought, it has a Engler injection using the above nozzle (which is really big). When the engine was built, the nozzle bosses were never drilled (as that is Tims method) for the air bleeds as they had nozzles under the runner to deliver the nitro. They did use the factory bosses for dribblers to start and warm the car.  Now on alky, the holes under the runner were plugged and the previous owner went back to the stock location with the nozzles and ran it for one race. I bought the engine and it was ran poorly since we fired it.

I pulled the nozzles out to clean them and noticed that they were completely caked up with white powder to the point to where I was using a pic to dig it out of the air bleed holes in the nozzle...thats where we realized that the intake was never drilled for the air bleeds.

I have to assume this is killing power as the fuel cannot atomize without it.

the picture attached is from a Engler manifold with the holes drilled.

8

Spud Miller's Cave / Optimal Fuel Pressure

« on: July 15, 2015, 06:01:32 AM »

What is the optimal fuel pressure for mechanical injection N/A?

Using your calculator on the FIE site we end up in the area of 69 lbs.

9

Spud Miller's Cave / Hilborn vs. Kinsler

« on: June 06, 2015, 07:55:53 AM »

With regards to the flowed pills from both companies, are they the same as in a .110 flowed kinsler is the same as a .110 flowed Hilborn?

10

Wanted to sell / Centerline wheels

« on: January 12, 2015, 05:31:47 AM »

For Sale:: Centerline 15x10, 5 on 5 with 4BS. Hoosier 30x10.5 with plenty of life still in them. 400.00

11

Wanted to sell / 1997 S&S Toter with 2008 Pace Trailer

« on: January 09, 2015, 07:50:23 PM »

http://www.racingjunk.com/Truck-Trailer-Combos/182358843/97-S-S-Toter-08-Pace-trailer.html

12

Spud Miller's Cave / Kinsler nozzles

« on: December 09, 2014, 06:37:17 PM »

Going thru the boxes of parts that came with the new engine and found these....engine has a Kinsler 3 piece with the nozzles in the ports. There are plugs under the runners that are plugged off and a set of nozzles, spare distribution block and hoses for that....

What is the purpose of the tips?

13

Wanted to sell / Misc. parts for sale

« on: December 07, 2014, 06:21:03 PM »

9.5in driveshaft with male and female coupler with one lock ring. $175.00


Pics available

call or text 812-278-6411

14

Wanted to sell / 481 KB Olds style Big Block Chevy

« on: November 20, 2014, 07:10:20 PM »

481 KB Olds style Big Block Chevy
Sonny Bryant Crankshaft (4” Stroke)
New Fowler Billet Aluminum Rods with two spares
8 New Sleeves
Arias Pistons 6:1 (8 spares with pins and buttons)
Extra new King rod bearings
Extra Main New Main Bearings Clevite 77 Performance
Roy Mirsh intake manifold
Dart 360 Solid Heads finished by Reher Morrison
Reher Morrison # 27CHMO
Inkenel exhaust valves
Titanium intake valves
Crower Roller lifters (7 spares)
Reher Morrison pushrods
8 spares 9.300
3 spares 8.600
5 spares 8.550
Jessel Rockers / Sig Erson Springs
4 spare roller rockers
Billet system 1 oil pump
RCD Gear Drive , mag offset, crank support
6-71 VRA Legal Blower
Spring loaded dribbler nozzles
Cirello Mag

15

Spud Miller's Cave / Mag Question

« on: November 02, 2014, 07:33:39 PM »

Switching over to a new engine that has a MSD 12. How far away can i mount the points box from the mag without worry?