Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - captmullette

Pages: [1] 2
1
Door Cars / 8.5 10 bolt posi change to spool?
« on: December 29, 2014, 07:26:28 AM »
got an old 8.5 10 bolt with a factory posi which is slipping, im gonna change over to a spool, ive been told ill have to change the carrier out for an open carrier to put the spool in no big deal I guess my question is...if I do this will I have to have my ring and pinion reset ?

2
Wanted to buy / reed cams catalog needed
« on: November 24, 2014, 02:47:19 PM »
got a reed cam in my car and am having a hard time getting specs without taking the cam out....if someone has a spec catalog and will sell it or whatever let me know....thanks bobby turner captmullette@gmail.com

3
Matt Shaff's Engine Shop / Re: max rpm's 6300 ???
« on: November 23, 2014, 02:48:01 PM »
thanks matt, kinda in a corner here, ive already got the AFR's and don't have a $1000 so.......

4
Matt Shaff's Engine Shop / Re: max rpm's 6300 ???
« on: November 21, 2014, 06:56:11 AM »
thanks for the input, sounds like good info for an uninformed person.....me....just trying to do this on a budget and not have to do it twice....do you think that my AFR 210 heads are too much, I can easily sell them and could have my heads machined for 202 valves thanks again for the help, don't want to run 9's just a good fun bracket car,

5
Matt Shaff's Engine Shop / Re: max rpm's 6300 ???
« on: November 19, 2014, 03:32:16 PM »
good question, I guess ill need some input, low budget, old motor, 355 2 bolt main, don't even know anything about the crank, forged or cast, got the heads cheap and really don't know that much about putting together a better motor

6
Matt Shaff's Engine Shop / Re: max rpm's 6300 ???
« on: November 19, 2014, 02:07:51 PM »
thanks matt, tearing the motor now changing the old iron double humps to AFR's and new cam.....looking at a lunati voodoo duration.050 is 241/249  gross lift is .525/546 flat tappet hyd. ...any thoughts ? heads are 210's

7
Matt Shaff's Engine Shop / Re: max rpm's 6300 ???
« on: November 18, 2014, 04:16:22 AM »
matt, I got a dial indicator yesterday and removed the rocker and checked the lift at the pushrod as best as I could, intake .322= .483, exh..324=.486......if you find it in your book I would really like a copy of the page etc.    thanks bobby

8
Matt Shaff's Engine Shop / Re: max rpm's 6300 ???
« on: November 16, 2014, 02:35:09 PM »
I think you've nailed it.....1.6 rockers any help.....???

9
Matt Shaff's Engine Shop / Re: max rpm's 6300 ???
« on: November 16, 2014, 02:49:37 AM »
 fuel system checked  o.k., same type exhaust, hydraulic cam.....can I help the rpms with 1.6 rockers ?  pulled the valve covers and I can turn the springs by hand on a closed valve.....not easy ign. is a procomp 6 al timing at 34 deg. didn't drive the chevelle but my driver said he remembered turning over 7000 ive heard some bad reports on procomp

10
Door Cars / Re: my door car......i guess.....also a new guy
« on: November 15, 2014, 04:03:23 PM »

View Profile
 Email
 Personal Message (Online)
 
Your Best Time: 1/4 11.90 1/8 7.39
Your Track: silver dollar raceway....reynolds ga.
Your Vehicle: 31 ford tudor sedan







max rpm's 6300 ???

« on: Today at 01:53:47 PM »


Quote

 
Modify

 
Remove

 

I put my old dirt track motor in my 31 ford bracket car, 355 sbc iron double humps small valve , flat top pistons, REED 3/8 mile dirt track cam, my partner cant find my cam card....this motor was built around 85/86 and sat in the back of a truck for 20 something years, rockers were loosened double springs all old and original.......my question is could I be running out of cam or weak springs or both....I just ordered a dial indicator to see what lift I have...thanks, hope I haven't sounded like a complete dumb ass.....as in the header it lays down at 6300 rpms

11
Matt Shaff's Engine Shop / max rpm's 6300 ???
« on: November 15, 2014, 01:53:47 PM »
I put my old dirt track motor in my 31 ford bracket car, 355 sbc iron double humps small valve , flat top pistons, REED 3/8 mile dirt track cam, my partner cant find my cam card....this motor was built around 85/86 and sat in the back of a truck for 20 something years, rockers were loosened double springs all old and original.......my question is could I be running out of cam or weak springs or both....I just ordered a dial indicator to see what lift I have...thanks, hope I haven't sounded like a complete dumb ass.....as in the header it lays down at 6300 rpms

12
Wanted to buy / need turbo 350 transbrake valve body
« on: November 03, 2014, 04:16:05 PM »
need turbo 350 transbrake valve body call 850-528-3306 or captmullette@gmail.com

13
Door Cars / Re: my door car......i guess.....also a new guy
« on: October 30, 2014, 07:43:00 AM »
thanks, yea I got them a year ago at Reynolds for $300.00, if my buddy jody hadn't been there nobody would believe it, also got an oil pan cam, 3 spring comp cam lifters , another set of lifters ,isky. roller rockers and 2 helmets

14
Door Cars / Re: my door car......i guess.....also a new guy
« on: October 30, 2014, 06:59:33 AM »
I had a friend build the chassis, 2x3  1/4"  tubing. the motor is a 355 sbc , iron double hump heads w/small valves 1.94. the motor came out of my 64 chevelle dirt track car that me and my buddy jody built in the 80's. ran it three years.when I decided to build a hotrod and got the body 31 sedan ,my buddy jody said he still had our old motor in storage and did I want it , well it's in the car as it came out of the other car 25 years ago except for the intake and carb, no rebuild ,yet, its got a custom grind john reed cam for a 3/8 th mile short dirt track, 2 bolt main w/1 rebuilt rod, turbo 350 4 link , 10 bolt 8.5 gm posi with a 4.56 gear, shortened with moser axles......I just pit the 4.56 in it and its laying over at 6400 rpm's , im going to have the heads checked, im either running out of cam or the 30 year old valve springs are a little tired. ill refresh it this winter and ive got a set of AFR 210 aluminum heads to put on it.....

15
Door Cars / Re: my door car......i guess.....also a new guy
« on: October 30, 2014, 06:20:55 AM »
yes it is and yes I was, were you there with your car? bowling green is a will do every year and now they are having a nostalgia good guys race in sept.

Pages: [1] 2