Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - hotrodharley

Pages: [1] 2 3 ... 6
1
Tow Vehicles / Re: 1974 Chapparal trailer
« on: January 27, 2018, 09:48:02 AM »
THE TRAILER YOU WAS ASKING ABOUT IS STILL FOR SELL;;THE BUYER HAD TO BACK OFF ON BUYING;HE KEPT CHANGING DATES ON COMING AND BUYING BUT WHEN HE DID SHOW UP HE SHOWED UP WITH A 4X4 WITH LIFT KIT;;TRY AND TELL HIM HE WOULD BE TO HIGH BEFORE HE SHOWED UP BUT SAID HE BEEN PULLING GOOSE NECKS WHEN I WAS STILL WEARING DIAPERS;;HE COULDN'T EVEN BACK UNDER TRAILER BECAUSE HE WAS TO HIGH;;I WANTED SO MUCH TO LAUGH IN HIS FACE BUT I KEPT MY COOL.

2
Tow Vehicles / Help
« on: January 16, 2018, 10:47:00 AM »
I have a 93 chevy dually with a 454 bbc with a pro charger..4l80e trans with a gearvendor overdrive behind it..has 3" cross over into singer 3" pipe into a single inlet to duel outlet flow master that goes into a big flate  converter looking muffle(i am thinking by it being at rear of truck then it is a resuranter but not sure there) it has 2  1/4" tail pipes comimg out of it but isnt factor outlets..got truck this way....truck is a monster when not hooked to trailer but when hooked to trailer it is a pig...anything i can do to get this truck to pull up the mountains in northen Nv. With my 38 foot chaparrel trailer...have trailer on here for sale thinking getting smaller lighter trailer but if can get my truck to tow it i would keep it because i really love the chaparral trailer and love to keep it

3
Wanted to sell / 38 foot chaparrel trailer
« on: January 14, 2018, 11:27:25 PM »
Have a nice rust free 74 chaparrel pouch style race car trailer.has 27'9" floor space..5' upper trailer space where the 4000 oman generator and 5hp air compressor is mounted..inside trailer is wired though conduit to 2 upper floscet shop lights..also has 110v plug in by fold down work bench and 2 more inside and one outside by second side door..air is hard line plumbed to 2 disconnects at work bench and 2 on outside of trailer..has wench for back ramp door and wench front of trailer for car..has 2 tool boxes mounted in front of trailer so not to take up floor space..has hyd. Tongue jack..when i got trailer it had hard to get 16.5" wheels and tires so replaced with new E rated 16" wheels and tires..at same time i replaced all wheel bearings and seals..brake shoes looked new..allso rewired complete trailer and replaced all lights with nee led lights..even has back up lights wired up..have lots of pics and trailer only had roughly 500 miles put on it after i did everything to it..selling due to my health and not able to race so sold fuel altered to a racer that already had a trailer..pleae if you tell me you buy then please buy..last person told me he eas buying but be couple weeks before he could come get it so told everyone it was sold but he never showed up or contacted me
after.
Asking $6500.

4
Wanted to sell / Re: 35 foot nostalgic car trailer
« on: August 15, 2017, 03:17:04 PM »
sorry guys;;I hit wrong key on price..should be $6500 so I changed ad

5
Wanted to sell / 35 foot nostalgic car trailer
« on: August 15, 2017, 10:50:30 AM »
ASKING $6500 OBO;;;NEED SOLD ASAP so very nogable;;;;
WILL TRADE FOR 26 FOOT OR LONGER TRAILER THAT IS 8 FOOT WIDE OR ABOUT THIS;;
text me first and if rather talk on phone just text me asking me to call;;;i get too many unknown phone calls so if don't know no# i don't answer phone;;
have many more pics and can do any detail pic you may need or want to see..not a big issue to walk outside and take pic..nothing to hide.will take as many pics as you want
Above Added: Tue August 15, 2017, 10:19 am EST
Description
1974 Chaparral 35 foot side pouch nostalgic trailer;;;28 foot floor space/2 foot tongue past trailer front/5 foot on upper deck where there is a 4000 watt generator and the 30 gal. 5hp 110 volt air compressor//compressor is hard lined to a discount fitting at a 6 foot fold down work bench and a quick disconnect air chuck on outside trailer by one of the side doors[has 2 side doors]the generator supplies 110 volt to 4 inside 110v. plugs and 1 110v plug mounted on outside of trailer by the 110 volt plug//has a wench front of trailer to wench car in and out and a wench in back part of trailer that opens and closes rear ramp door//has hydraulic tongue jack that works off the 12v dc battery that operates front wench and also used to start generator and the rear wench has it's own 12 volt dc battery//also can plug trailer into outside ac source//has all new wiring and new led lights//also reverse lights on back of trailer that is wired into the 7 pong trailer plug/has a 110 volt wire running to middle of trailer to hook up a roof ac system///new wheel bearings and wheel seals with new 16" 10 ply tires//paint is peeling pretty good so could use new paint job but if not ready to paint then can just remove my lettering and art work off trailer and put your own on it till ready to repaint//they are only vinyl//the trailer has only 500 miles on it after I did all the new stuff on it;;very ready for road use///be great trailer for a nostalgic racer or for a cackler car;; more pics on racingjunk.com ad#182920396

6
want to trade my fuel altered for a pro/street car ot truck or pro/street street rod or a cakle car;;
this is a new 125" fuel altered;;chassis has another year left on NHRA cert;;good for down to 6 seconds;;everything new;540 dark block/brodex bb2 heads[w/port&flow work]JE 11.7 pistons/GRP alum rods/BDS comp intake/littlefield 12-71 blower/27%od/GREADOT modified hat/suppermag111[upgraded by Spud]fuel system flowed by Spuud/comp eng. chrome molly full floater rear end/M/W brakes/M/W axles/car will tech; $35000 for car/ $45000 for car/38ft chaprel trailer/generator/compressor/wrench for ramp door and car/new wheel bearings and new 10ply tires;;;sure i'm missing a lot;;have build pics and papers on everything;;text only on phone;i will call you after you text;in pic car has the B&U HAT AND BLACK VAOVE COVERS..IT NOW HAS POLISHED V/C AND POLISHED GERADOT HAT

7
Wanted to sell / pulley spacer
« on: June 24, 2015, 02:45:12 PM »
1/2" blower pulley spacer. 1/2" thick...$25.00 with FREE shipping in USA.Will ship international but buyer pays any shipping cost over $5.00

8
Wanted to sell / blower front cover
« on: June 23, 2015, 07:51:35 AM »
show polished Little Field 6-71 up to 14-71 blower front cover with black anidized pressure release;;half circle style cover;;$125.00+shipping

9
Altereds / front end wobble
« on: June 06, 2015, 07:45:20 PM »
made a light pass with car last weekend and on top end of track[1/8th mile track]my front end started wobble[steering wheel shaking back and forth]seems like as soon as I lifted on throttle it stoped the wobble I believe.happen so fast can't remember if it stopped on it's own or when I lifted or if I accelerated and stopped it;;tires are new but has been sitting on car for roughly7 years;;king pins and wheel bearings are good;;;What do I need to do[new spindle mount wheels]to hopefuly fix this issue;

10
Wanted to buy / Re: tunnel ram with injection hat
« on: May 11, 2015, 07:08:56 PM »
Thanks everyone for your replies;;I found him one on racingjunk.com already;

11
Matt Shaff's Engine Shop / break in new flat tappet engine
« on: April 20, 2015, 11:54:23 PM »
on my fuel altered engine[540 blown alcohol injected]eng it was a no brainer;;filled up with brad penn 50wt and not worry about break in;;but i'm finishing up on a 454 bbc NA street eng with mild hyd performance cam;;a street and show car;been 4 hours reading about all the different oil and break in oil I'm to use for flat tappet eng..bad thing is most post not dated and one post says fill with diesel oil then next post says no on diesel oil that they removed zinc from them also;;;also they talk about putting this expensive break in oil in then droping it after 30 mints then doing it agin then dropping after 100 miles an so on and so on;;;IS there just a straight up oil that I can put in eng and do my 2000rpm/20 mint cam break in process and then just drive car till time for a normal 3000 mile oil change without all the adding break in stuff and removing after a hour because it turns or looks like water;;also what weight now days should be used?

12
Spud Miller's Cave / Re: fuel pump size
« on: March 28, 2015, 10:42:30 AM »
Thanks Spud;;;Will tell him to pass on it then;;what size enderle pump would you recommend him to get then?

13
Spud Miller's Cave / fuel pump size
« on: March 28, 2015, 12:14:57 AM »
friend has a 454 sbc with 13-1 comp;[has no heads or cam yet]got him a tunnel ram with bird catcher. going run alcohol.Also found a hilibrand PG-150A pump;;Will this pump work for his combo?open Also what head size and cam size should he go with?

14
Wanted to buy / tunnel ram with injection hat
« on: March 04, 2015, 04:55:04 PM »
a buddy building his first dragcar and is looking to buy a tunnelram with a bug or bird catcher on it;;a complete system or what ever you may have to build a system from;;pics/prices to darksidefuelaltered@gmail.com

15
Altereds / Re: What did you do on your Altered TODAY?
« on: February 24, 2015, 05:29:56 PM »
got my rcd blower starter today;;is there a big difference between weight of my steel starter frame and a aluminum one?if so who has best price on them?

Pages: [1] 2 3 ... 6