Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - dgrossmann44

Pages: [1]
Roo Man's Room / Tach with Mag & Rev Limiter
« on: February 10, 2020, 11:44:55 AM »
 Changing over to Mag and using FIE rev limiter with MSD SW & 2 step
1) can the Tach or shift light be run off the Crank trigger somehow? Or do we have to use a pulse signal activator.
2) In either case should we use solid core  or suppression wires.
Thank You

Roo Man's Room / Re: Points mag rev limiter
« on: January 27, 2020, 04:53:50 PM »
Good for both Thank You

Roo Man's Room / Towing with a strap
« on: January 27, 2020, 04:15:00 PM »
What is the best spot to connect the strap to the car. We’ve been Connecting to center of the front axle. Steering feels little different after pulling it around a bit. Has a P&S box  175” FED Thanks

Roo Man's Room / Points mag rev limiter
« on: January 27, 2020, 02:54:12 PM »
Is the FEI-RPMLIMIT  points mag RPM limiter relay for internal or external coil mag?
Thank you

Spud Miller's Cave / Mag rev limiter
« on: April 27, 2019, 12:36:10 PM »
We purchased the FIE  rpm limiter relay along with the switch. The mag we have is joe hunt internal coil. Can We get a little help with the suggested point of connection for the positive and negative wires at the mag. The only external connection is the ground lug correct? In the flat bottom we never ran a limiter. Seemed like a good idea at the time! I guess?  Thank you

Front Engine Dragsters / Re: wheelie bar
« on: March 05, 2018, 09:39:19 PM »
We don’t have any info yet on how the car leaves, squat etc... the bar is a single wheel and almost 7 foot . We are newbies formally boat guys. This is all new to us. The car came with the that size tires so we just replaced them with new. We welcome any input that will help us. This was a project that my son and I started with pops who passed away just as we were completing the car. my experience was on water pop raced on asphalt and was our leader. We miss him but I know he wants us to carry on. So we will give it our best. We  Thank you for any and all advise

Front Engine Dragsters / wheelie bar
« on: March 05, 2018, 09:55:03 AM »
Looking for a starting point dimension for setting the wheelie bar of the pavement ? Have a 175" FED with a BBC 33X15X15 Rear tires. Also how many RPMS should we expect to spin during a burn out  w/5500 stall. Thank You

Front Engine Dragsters / Re: crankcase evac
« on: November 21, 2017, 02:36:43 PM »
Jon , Your two cents are well worth it Thank You

Front Engine Dragsters / crankcase evac
« on: November 21, 2017, 12:52:51 PM »
Is a vac pump the only option when running zoomies .

Front Engine Dragsters / Re: Chiller Connection
« on: January 20, 2016, 01:45:02 PM »
Jon, Thank You for taking the time to educate. I was thinking more of a portable chiller I should have been more specific.  We previously ran a Flat Bottom Boat so this is new to us and appreciate any advice we can get. We have crossed paths at the track in fact you sold me my front wheels and tires, Thank Again!

Front Engine Dragsters / Re: Chiller Connection
« on: January 20, 2016, 12:46:42 PM »
it is alky w/aluminum heads

Front Engine Dragsters / Chiller Connection
« on: January 20, 2016, 07:01:57 AM »
First we are beginners. Just finished the car and we are building a chiller. Can we get a little help on connection? Do we connect input to each head an exit out the top of the manifold?

Pages: [1]