Messages

1561

Spud Miller's Cave / A/fuel setup

« on: January 01, 2014, 08:58:28 AM »

 Spud,

 Wonder what I would need for good A/fuel setup.I have Hemi short blocks that I ran in TA/D all good stuff. Heads I have 2 sets of buildable BAE fuel style(not fat head) Have set of msd mag 12's(wish 44's). Main question trans.Can it be setup to work with glide. I have clutch setups ,just sold trick titainium cam(dumb___) no lenco parts.Chassis is built to 2.2c specs so I should be good there.

 Trans ,pump size and cost for you to setup a system for it.If I decide to set one up it would be for full amount allowed by rules. Just Idea Im kicking around.Hnave some 1200 pumps I can sale or trade off for smaller one that fits within the rules.

1562

Your Builds / Photo Gallery / Re: The latest car out of my shop

« on: December 23, 2013, 04:14:34 PM »

We need a LMAO smiley face on the list for^^^^^. I woud post mine from 1969.It was plastic pedal car but it was in all honesty a FED pedal car.

1563

Front Engine Dragsters / Re: days gone by pictures

« on: December 23, 2013, 04:11:23 PM »

Dang Bill you been around this a while. Most of those probably made before i was born.

1564

Wanted to buy / Re: Looking for beadlock 15"or 16"X 11" or 12"wide with about 3.5"bs

« on: December 20, 2013, 05:56:00 AM »

Might look inot getting some old ones converted. I have a set of 16x16 that I talked with weld about getting cut and converted to 15x 14 dbl beadlocks.Price was 1000 bucks if they can do it.Was told If I would ship them they could tell me.I think Im going to ship one and if do able I will ship other wheel,have to check cost of one vs two. I figure 1000 bucks is better than spending 1400 to 2000 for new ones and used ones in this size are really hard to find.

1565

Front Engine Dragsters / Re: check this one out .... ebay FED

« on: December 20, 2013, 05:51:34 AM »

Mine are not big enough to make a pass in that. Cool but would have to be for cackle car IMO.

1566

Front Engine Dragsters / Re: What did you do on your Front Engine Dragster TODAY?

« on: December 15, 2013, 05:48:01 PM »

So they are selling printing plates,paper and inks to print hundred dollar bills?

1567

Wanted to sell / Re: Race stuff

« on: December 01, 2013, 03:50:09 PM »

BC on wheels and ratio on shorty set for glide? Looking for 5 on5 an 1.69 low .

1568

Roo Man's Room / Re: Clutch Pedal

« on: November 30, 2013, 07:09:58 AM »

9 years of alky funny and dragster and used pedal without either.Was mounted on stud the was thru tube with clutch pedal welded to it.Worked fine. Question how much money do you want to spend and do you need the bearing piece. I'm Sure its nice and super smooth.

1569

Front Engine Dragsters / Re: home made tube shifter

« on: November 28, 2013, 09:17:24 AM »

Same basic idea.If parks would put better pics on site i would have had easier time designing mine. I got the basic function of it figured out from the pics and worked out rest

1570

Wanted to buy / anglia spindles

« on: November 26, 2013, 12:48:24 PM »

Need set of spindles for fed anglia style.Going to buy new ones and figured asking around could n't hurt.

1571

Front Engine Dragsters / Re: home made tube shifter

« on: November 25, 2013, 04:19:43 PM »

with mine you can have p-r-n 1-2 or p-r-n-2-1  the pattern is determined by valve body and trans linkage not shifter inn this case. Mine will be p r n 2 1 so I caN USE SHIFT SOLENOD  for 1-2 shift. For burn out Ill just push it into 2nd and hammer it,stop tist push twist push and will be in reverse.

1572

Front Engine Dragsters / Re: home made tube shifter

« on: November 25, 2013, 04:06:53 PM »

On mine you have to twist it to go to netural 1st to second is just straight slot.Twist and push forward for netural,twist again push forward for reverse twist oppisite and push while using foot assist that mount on trans for park.If I have to I can add flip lever for lockout.Not cocerned about neutral safety switch never had one and never been asked by tech about it.

1573

Front Engine Dragsters / Re: home made tube shifter

« on: November 25, 2013, 06:44:56 AM »

Built one myself using two pieces of moly tubing and seems to work great weighs less than lb.Well until I added the shift solenoid.

1574

Front Engine Dragsters / Re: What did you do on your Front Engine Dragster TODAY?

« on: November 22, 2013, 04:13:56 PM »

Glen I thought YOU said no cuss words and thats real nasty one you guys keep using.

1575

Front Engine Dragsters / Re: What did you do on your Front Engine Dragster TODAY?

« on: November 22, 2013, 02:29:14 PM »

what is this underdrive you speak of?