Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Wrenchbender

Pages: [1]
1
Gassers / Re: My Willys gasser
« on: August 06, 2015, 11:40:53 AM »
Thanks for the compliment and yes it gets a lot of looks but I just get tired of the rat rod comments lol not to mention the candy lace panel paint job that is planned would really bring it to the next level of awesome

2
Dan Dishon's Transmission Den / Re: Hydro help needed
« on: August 06, 2015, 11:38:35 AM »
Thanks for the info guys I have already been to the local heat treat shop even tried to get modine to do it which they furnace braze all he time but they do all stainless and the oven temp is way to high I will try the suggested converter places you have suggested thanks again for the info

3
Gassers / My Willys gasser
« on: August 05, 2015, 12:49:51 PM »
I guess I should post some pics of my gasser I've had several still have some of them lol. The current one is a 1940 Willys pickup it has a 311 cubic inch small block Chevy 4-71 blower and a 4-speed frankland quickchange it has quarter leaf rear suspension and Chevy truck ladder bars all of it is straight outta 1963 granted it's not the prettiest thing as of yet but in due time it will be painted and done but for now it's tea and tune lol anyway here are a few pics







And one last one where I was running the hairy hauler a well know gasser from the 60's






4
Dan Dishon's Transmission Den / Re: Hydro help needed
« on: August 05, 2015, 12:06:20 PM »
There are no converter shops near me and I called b&m talked with don spar he chuckled said they don't do that anymore and haven't for nearly 40 years however he did send me some very necessary literature and answered some questions I had so if you have a converter shop you use I am open to sending it off just need some contact info   Thanks

5
Dan Dishon's Transmission Den / Hydro help needed
« on: August 05, 2015, 08:18:15 AM »
I have a b&m hydro and I need the fins in the torus wheels in the converter furnace brazed does any one know a place I can get that done I know this is ancient technology but the car it's going is is too lol this is the only thing I lack in finishing this part of the drivetrain any info is greatly appreciated.   

Thanks

6
Your Builds / Photo Gallery / Re: My TE-448
« on: July 22, 2015, 07:52:07 PM »
Cool just need a chain drive blower!

Thanks  I would like to have one but haven't found an affordable one that was all there lol I actually looked at one about a month ago it was on a olds engine and it could not be bought plus I just couldn't bring myself to separate the setup then cut it up to make it fit the caddy however I was able to see all the internals and it wouldn't be hard to build one I just don't have time

7
Your Builds / Photo Gallery / Re: My TE-448
« on: July 22, 2015, 08:02:16 AM »
One more


8
Your Builds / Photo Gallery / My TE-448
« on: July 22, 2015, 07:54:54 AM »


Well folks new guy here above pic is the chassis research TE-448 style dragster I am currently working on hoping to have it done for next season it has 100" wheelbase 8 3/4 Chrysler rear 322" flathead caddy engine with a 4-71 blower and will have a 2-port hilborn injector burning alky  it is a clutch car with a three speed ford Trans that will probly only use high and reverse  I welcome any and all constructive advice as I am here to learn from those who have been there and done that I'm not trying to win the top eliminator prize here just have some fun and see the smoke roll off the slicks lol I live three miles from Mokan dragway so test and tune is never an issue for me lol here are a few more pics




Pages: [1]