Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Candy-Man

Pages: [1]
1
Wanted to sell / 392 Hemi's (X2), Halibrand Dragster Spindle Mount Rims
« on: September 11, 2017, 02:29:50 PM »
For Sale:

1) Two 1958 "392 Hemi's" . Motors are apart. Price includes: Block, Heads, Rockers & Crank. Other pieces for sale as well.... $2,000 each, FIRM....

2) Hedman Dragster 2" tubes for 392 hemi, zoomie hedders, silver ceramic coated, new $1,100 US... Selling for $700...

3) One piece Fiberglass race 'T' bucket with turtle deck (trunk), weights 30 lbs, $600....

4) 3 pairs of 392 bare heads, $175 per pair....

5) Milodon 392 hemi gear drive, new, $300....

6) Chrome moly wheelie bars, powder coated flat black, with adjuster coil springs, new never used, $375.....

7)  Enderle Barn Door Blower Injector, with scoop and stainless steel lines, highly polished mirror like, $1,200 FIRM....

8) Two sets of Halibrand, magnesium spindle mount, funny car rims, mint condition, $1,200 pair....

9) Accel Pro hemi race wires, $100 pair....

10) Moon 4 quart puke tank with breather and cast brackets, new, $300

11) 392 hemi 'nitro / fuel' roller cam, roller rockers and springs, new, $600...



Contact : neilcandy@xplornet.ca or call # (613) 353-7572

Parts located 3 hours north of Syracuse NY...

2
Wanted to sell / Donovan Hemi Stands, Rockers, etc
« on: March 24, 2014, 04:54:31 PM »
Chrysler Hemi, complete set of Donovan Stands, Rockers, Solid Shafts, etc.

Pictures show it all on a Nitro Burning 392.

$1,300.00

Thanks, Neil...

3
Gassers / '40 Willys P/U Box Measurements
« on: March 01, 2014, 06:32:07 AM »
Hello :  I will be starting my '40 Willys Truck build this summer and I am looking for a few general measurments for the box which I will be building.  What is the general heigth of the box, assuming the bottom of the box does not extend past the bottom of the frame rail ?   Second, what angle where the gun rails bent and the width of the gun rail ?

I was thinking 21" tall box, including the gun rails would look just fine !   The motor will be a 409 !

Thanks...

4
Wanted to buy / 392 Magneto For AA/FA
« on: February 28, 2014, 10:51:04 PM »
Wanted :  392 Magneto for a AA/FA...

Thx....

5
Wanted to buy / LENCO CS2 Rear Mount Shifter
« on: March 20, 2013, 11:13:56 AM »
Wondering who may have a rear mounted manual shifter for a CS2, 2 speed with reverser ?

Thx, Neil...

6
Roo Man's Room / AA/FA : Fuel Altered Axle With Coil Overs
« on: February 14, 2013, 05:22:26 AM »
What coil overs (Shock Length & Spring Rate) are the AA/FA altereds running on their front axles ?   I understand the front ends are near solid, with very limited suspension.  THx....

7
Roo Man's Room / Lenco CS1 or CS2 Transmission For A "AA/FA"
« on: February 08, 2013, 06:02:17 AM »
2 Spd, 19% underdriven CS2 Lenco for a  AA/FA ?    Or should I go for the CS1 ?

8
Wanted to buy / Lenco OR B&J 2 Speed With Reverse
« on: February 02, 2013, 03:48:19 PM »
I am looking for a 2 speed with reverse, 25% underdriven 1st gear...  Either a Lenco or B&J for my AA/FA which I will begin to build soon...

Thx....

Pages: [1]