Author Topic: Pump flow and nozzle size  (Read 7950 times)

Offline Cajuninjector

  • Jr. Member
  • **
  • Posts: 64
    • View Profile
  • Your Best Time: 7.50@176
  • Your Engine: SBC 406 Alky Stacked Hilborn
  • Your Track: SWJFA
  • Your Vehicle: 225" FED-Wizard Race Cars
Pump flow and nozzle size
« on: May 05, 2013, 05:22:31 PM »
Hey Spud, I sent you two hilborn pumps after last season so you could check and flow them. I have lost the flow cards you sent back with the pumps. I remember they flowed around 6.5 gpm but I would like to know what rpm this flow was at.
Also I have some nozzles in my hilborn that some say are too big. They have 18BS stamped on them. It's a hilborn 3 piece 2-3/4, sbc 406 with iron eagle 23deg that flow pretty good. 
Could this be too low of a pressure system? 
Thanks
Go Hard or Go Home

Offline gregm784

  • Sr. Member
  • ****
  • Posts: 384
    • View Profile
    • Means Racing
  • Your Engine: 365" GenIV SBC
  • Your Track: Famoso Raceway
  • Your Vehicle: 1997 Stirling 200" FED
Re: Pump flow and nozzle size
« Reply #1 on: May 05, 2013, 06:15:22 PM »
When pumps are measured for max flow, it is at a pump speed of 4000 RPM, or 8000 RPM engine speed.

I'll let Spud work on th enozzles, but they sound close.  would be about a 36 enderle. May be a tad big.  Might need a 25-28 enderle or a 12-14 hilborn.
Greg
El Dorado County, CA
www.meansracing.com

Offline Cajuninjector

  • Jr. Member
  • **
  • Posts: 64
    • View Profile
  • Your Best Time: 7.50@176
  • Your Engine: SBC 406 Alky Stacked Hilborn
  • Your Track: SWJFA
  • Your Vehicle: 225" FED-Wizard Race Cars
Re: Pump flow and nozzle size
« Reply #2 on: May 08, 2013, 07:58:58 PM »
Thanks Greg.
Go Hard or Go Home

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1910
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: Pump flow and nozzle size
« Reply #3 on: May 15, 2013, 08:07:46 AM »
I normally run 34 to 38 with same size pump depending on motor. IMO 34 to 36 would be good starting point for 400 ci motor and I would lean towards the 34's for little more pressure,these are enderle nozzles never used others.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline Spud Miller

  • Global Moderator
  • Sr. Member
  • *****
  • Posts: 332
    • View Profile
    • Fuel Injection Ent., LLC
Re: Pump flow and nozzle size
« Reply #4 on: May 24, 2013, 08:16:21 PM »
Hey Spud, I sent you two hilborn pumps after last season so you could check and flow them. I have lost the flow cards you sent back with the pumps. I remember they flowed around 6.5 gpm but I would like to know what rpm this flow was at.

Our tags show the flow at:
1800 pump RPM @ 50 PSI
4000 pump RPM @ 100 PSI

Your 6.5 GPM number was the 4000 pump RPM figure (8000 engine RPM).

Our flow tags are now decals so you can stick them in your log book, in the lid of your toolbox, inside the door of your trailer...someplace safe.

Quote
Also I have some nozzles in my hilborn that some say are too big. They have 18BS stamped on them. It's a hilborn 3 piece 2-3/4, sbc 406 with iron eagle 23deg that flow pretty good. 
Could this be too low of a pressure system? 

Some people run much smaller nozzles in a motor that size, but most who do that don't spin the motor up very high. Those nozzles will work just fine for you, just at a bit lower system pressure. If you're only hitting say 7000 RPM at the top end, 12's would be better. If you're spinning to 9500 on a pass, then 18's are just what you need.

The "18" means they flow .18 GPM of .792 SG liquid @ 30 PSI.  The "B" means they were meant for a turbo application and the "S" means they have a screen tip.


Fuel Injection Enterprises, LLC
     Mechanical Injection
     Magnetos
     EFI Conversions