Author Topic: Chassis - paint, powdercoat or POR?  (Read 3372 times)

Offline Harv

  • Newbie
  • *
  • Posts: 5
    • View Profile
  • Your Best Time: None
  • Your Engine: Holden alky 154ci
  • Your Track: Sydney Dragway
  • Your Vehicle: Building a IHRA-certified nostalgia FED
  • General Location: Sydney Australia
Chassis - paint, powdercoat or POR?
« on: September 03, 2023, 10:27:11 PM »
Getting closer to having the FED together. Looking to put some form of protection over the chassis, but not sure whether to have a panel shop paint it, a shop to powdercoat or to DIY it myself with POR chassis coating.

Needs to be neat and tidy and presentable, but not show-car perfect (as an example, my panels are painted in purple metalflake, but not on the inside). Prefer something that I can touch up later if I damage it or need to ad a bracket tab.

Appreciate your experiences please.

Cheers,
Harv

Offline THE FRENCHTOWN FLYER

  • Sr. Member
  • ****
  • Posts: 360
    • View Profile
  • Your Best Time: 8.28@168 door; 9.00@147 6-cyl alt; 8.53@160 RED
  • Your Engine: 300 Ford six NA w/ crossflow and prod. heads
  • Your Track: Milan, Thompson
  • Your Vehicle: (3) Advanced Chassis altered , The Last Logghe altered, '30 RPU
  • General Location: North Coast
Re: Chassis - paint, powdercoat or POR?
« Reply #1 on: September 04, 2023, 08:37:49 PM »
Most cars that get powder coated eventually have to add welded on tabs, fix cracked welds or just have the stuff blister off somewhere.

My vote is acrylic enamel with hardner.

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1913
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: Chassis - paint, powdercoat or POR?
« Reply #2 on: September 05, 2023, 05:50:19 AM »
Would never pwdercoat a chassis for above reason. I know I will be adding or changing something. With paint sand off. weld touch up paint done.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline Harv

  • Newbie
  • *
  • Posts: 5
    • View Profile
  • Your Best Time: None
  • Your Engine: Holden alky 154ci
  • Your Track: Sydney Dragway
  • Your Vehicle: Building a IHRA-certified nostalgia FED
  • General Location: Sydney Australia
Re: Chassis - paint, powdercoat or POR?
« Reply #3 on: September 05, 2023, 09:36:01 PM »
Thankyou both - appreciated.

Cheers,
Harv

Offline lake_harley

  • Sr. Member
  • ****
  • Posts: 262
    • View Profile
  • Your Best Time: 7.06 @99.58 - 1/8 mi.
  • Your Engine: Carbureted, gas mild 305 Chevy
  • Your Track: Jeffers Motorsports Park - Sikeston, MO
  • Your Vehicle: 145" FED
  • General Location: SE Missouri
Re: Chassis - paint, powdercoat or POR?
« Reply #4 on: September 07, 2023, 07:00:58 PM »
I really don't have anything different to add, but I too vote for paint. I know powdercoat is really held in high regard, but beyond the "need to add a bracket and can then just touch up the paint" I see a bigger problem with it. It's "so good" that it can flex to some extent.....it's basically plastic. That's where I have a problem with it in that if a joint is developing a crack paint will crack too and eventually a slight rust line might develop which might might be discovered and can be corrected before a big failure.

I did my FED chassis with a electrostatic paint system I have from my fabrication business days. Paint used was an enamel. Looks fine to me and MUCH cheaper than powdercoat too.

Lynn

Offline Harv

  • Newbie
  • *
  • Posts: 5
    • View Profile
  • Your Best Time: None
  • Your Engine: Holden alky 154ci
  • Your Track: Sydney Dragway
  • Your Vehicle: Building a IHRA-certified nostalgia FED
  • General Location: Sydney Australia
Re: Chassis - paint, powdercoat or POR?
« Reply #5 on: September 09, 2023, 12:16:52 AM »
Thankyou. Good logic on the flex vs crack too.

Cheers,
Harv

Offline gordon

  • Newbie
  • *
  • Posts: 43
    • View Profile
  • Your Track: Sacramento
  • Your Vehicle: FED
Re: Chassis - paint, powdercoat or POR?
« Reply #6 on: September 11, 2023, 10:59:26 AM »
I am getting ready to cold blue my chassis . always wanted to do one this way. Lot of work but what the Hey.  Will never powdercoat one again . 

Offline Paul New

  • Hero Member
  • *****
  • Posts: 745
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: Chassis - paint, powdercoat or POR?
« Reply #7 on: September 26, 2023, 07:16:47 PM »
My car is cold blue it will still rust but sure does look great!!

Offline gordon

  • Newbie
  • *
  • Posts: 43
    • View Profile
  • Your Track: Sacramento
  • Your Vehicle: FED
Re: Chassis - paint, powdercoat or POR?
« Reply #8 on: September 30, 2023, 10:59:53 AM »
Hi Paul, what brand of Cold Blue/Tool black did you use ? Through the years I have used two different ones from Brownells supply and one generic tool black bought on line . The Brownells Oxfo blue seemed to work the best but I am always looking for better.

Offline Paul New

  • Hero Member
  • *****
  • Posts: 745
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: Chassis - paint, powdercoat or POR?
« Reply #9 on: October 02, 2023, 06:48:35 PM »
I used Precision Brand Tool Black

Offline dusterdave173

  • Hero Member
  • *****
  • Posts: 638
    • View Profile
  • Your Best Time: 5.38in 1/8th
  • Your Engine: 355 CI SBC
  • Your Track: Mooresville, NC
  • Your Vehicle: CenPen 200 inch FED
Re: Chassis - paint, powdercoat or POR?
« Reply #10 on: October 03, 2023, 12:54:07 PM »
Chrome moly is not prone to rust--the pro cars are just wiped down with oil or wd40 or whatever--You will have to fix cracks and add brackets etc  You will--no way around it--I painted mine with acrylic enamel but if I did another would wipe her down and go  Grinding off POR or powdercoat sounds crazy to me--they flex they crack just no two ways about it--if you run a season or two and can't find a crack you did not look hard enough--find--weld-smile-keep rolling
I have always had a fascination with fast cars at the expense of more normal character development