Author Topic: under driving a pump  (Read 1586 times)

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1910
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
under driving a pump
« on: November 27, 2022, 07:51:48 AM »
Is anyone running a mech. pump with an under drive. I have a 7 GPM pump on the car now. NA 482 ci. Sin ce bypassing about half the fuel I was wondering about underdrive for pump bypass less and running at lower pump rpm has to be easier on the pump. Now how to figure fuel system. Using Spud's calculator. If use 10% drop in fuel flow I have chart that shows it looks like would expect. How accurate with a lot of assumed and no real flow bench info?
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline tcoupekyle

  • Sr. Member
  • ****
  • Posts: 355
    • View Profile
  • Your Best Time: 4.70 1/8
  • Your Track: Houston Motorsport park
  • Your Vehicle: 225" slip joint FED
  • General Location: Houston
Re: under driving a pump
« Reply #1 on: November 27, 2022, 10:35:59 AM »
I am also curious. I have a 110 pump and it’s just a bit much I think running a .160 pill.

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1910
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: under driving a pump
« Reply #2 on: November 27, 2022, 11:13:51 AM »
From what I can gather it runs pretty linearly. A 10% reduction in drive equals 10% fuel. Now that is generalization of about 10 pumps out of my Gorr sheets.  Hoping for input from anyone having done it real world not calculations .

 
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline slingshot383

  • Full Member
  • ***
  • Posts: 146
    • View Profile
  • Your Best Time: 1/4 mi. 7.95 @ 168
  • Your Engine: Chrysler, alcohol, 528 cu.in.
  • Your Track: Gateway Motorsports Park (the Swamp)
  • Your Vehicle: Undercover Chassis 23T altered
Re: under driving a pump
« Reply #3 on: December 02, 2022, 02:13:46 PM »
Anybody that flows pumps (or has a flow chart from a pump being flowed) you should be able to make easy calculations from it.  A flow chart will compare flow rate to rpm, so take your reduction percentage into rpm and match that to the graph and you'll have your new flow numbers.
Undercover 23T Altered, big block Mopar
Member of the Torque and Recoil Club

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1910
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: under driving a pump
« Reply #4 on: December 05, 2022, 01:41:17 PM »
I have chart for one pump and total flow of other pump. Easy enough to know flow of one with full chart. Now that I have had 3 or 4 confirm that it changes same as drive change I know what one with just total flow number will do.

Have a fuel flow sensor for data logger coming and think I can convert it to use on home made flow bench. At least readings will be the same as what I get when it is on car since it essentially the same piece as long as rpm matches.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline slingshot383

  • Full Member
  • ***
  • Posts: 146
    • View Profile
  • Your Best Time: 1/4 mi. 7.95 @ 168
  • Your Engine: Chrysler, alcohol, 528 cu.in.
  • Your Track: Gateway Motorsports Park (the Swamp)
  • Your Vehicle: Undercover Chassis 23T altered
Re: under driving a pump
« Reply #5 on: December 08, 2022, 02:35:20 PM »
Knowing fuel flow at any given rpm is better information than pressure is!
Undercover 23T Altered, big block Mopar
Member of the Torque and Recoil Club