Author Topic: I need your help- Magneto kill switch circuit  (Read 3067 times)

Offline 58Apache

  • Newbie
  • *
  • Posts: 20
    • View Profile
  • Your Best Time: none
  • Your Engine: 572 Aluminum Keith Black Chevy
  • Your Track: Top Gun raceway, Fallon Nv
  • Your Vehicle: 58 Chevy Apache 3100 truck
  • General Location: Reno, Nv
I need your help- Magneto kill switch circuit
« on: February 20, 2020, 08:13:07 PM »
Ok, So here is what I have. I will have a Mag kill switch in my cab on my switch panel, but then I will need another Kill switch at the back of my truck for emergency shut off. I was thinking of a series circuit. Hot side of the coil to the positive side of the kill switch in the cab. Negative side wire from that switch to the back switch hot side, and negative side of the back switch to motor for ground. This way if either switch is switched off it kills the mag. Any thoughts?   

Offline hotrodpete

  • Newbie
  • *
  • Posts: 45
    • View Profile
  • Your Best Time: 9.8@138
  • Your Engine: Early hemi
  • Your Track: St Thomas
  • Your Vehicle: Rooman Fiat altered
  • General Location: Orillia, Ontario
Re: I need your help- Magneto kill switch circuit
« Reply #1 on: February 21, 2020, 04:09:49 AM »
You could use a FR1010 flaming river battery diconnect switch with mag kill. You need one anyway so if this fails at a track you have a better chance of replacing it.

Offline lake_harley

  • Sr. Member
  • ****
  • Posts: 255
    • View Profile
  • Your Best Time: 7.06 @99.58 - 1/8 mi.
  • Your Engine: Carbureted, gas mild 305 Chevy
  • Your Track: Jeffers Motorsports Park - Sikeston, MO
  • Your Vehicle: 145" FED
  • General Location: SE Missouri
Re: I need your help- Magneto kill switch circuit
« Reply #2 on: February 21, 2020, 06:09:08 AM »
I was thinking of a series circuit. Hot side of the coil to the positive side of the kill switch in the cab. Negative side wire from that switch to the back switch hot side, and negative side of the back switch to motor for ground. This way if either switch is switched off it kills the mag. Any thoughts?

If you do the series as described I don't believe it would work as intended. With what you described, if you flip the cab switch to kill the engine all you'd be doing is sending voltage to the rear switch and with it still "open" the engine would continue to run.

I'd say the two switches should be "parallel", with the coil wire going to the "hot" side on both switches with the negative sides going to ground. With that, if either switch is flipped to kill the engine, the coil's current would go to ground and kill the engine.

I'll admit to having no experience with a mag in a drag car, but I believe I understand the kill switch process. If I'm wrong, someone PLEASE correct me and I'll crawl back under my rock.

Best wishes.

Lynn

Offline Paul New

  • Hero Member
  • *****
  • Posts: 745
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: I need your help- Magneto kill switch circuit
« Reply #3 on: February 21, 2020, 06:47:38 AM »
I’ve used a NC contact with a relay years ago.  By powering on the battery switch on it will open the contacts and when you de-energize the relay the contact closes grounding out the mag.  What kind of mag will you be running?

Offline THE FRENCHTOWN FLYER

  • Sr. Member
  • ****
  • Posts: 360
    • View Profile
  • Your Best Time: 8.28@168 door; 9.00@147 6-cyl alt; 8.53@160 RED
  • Your Engine: 300 Ford six NA w/ crossflow and prod. heads
  • Your Track: Milan, Thompson
  • Your Vehicle: (3) Advanced Chassis altered , The Last Logghe altered, '30 RPU
  • General Location: North Coast
Re: I need your help- Magneto kill switch circuit
« Reply #4 on: February 21, 2020, 08:41:12 AM »
What Paul said. Use a relay in the cockpit switch circuit.

BTW The 4-pole master shutoff by Flaming river and others has much less current carrying capacity on the two magneto terminals than the other two terminals. I have had those terminals go bad.

Offline 58Apache

  • Newbie
  • *
  • Posts: 20
    • View Profile
  • Your Best Time: none
  • Your Engine: 572 Aluminum Keith Black Chevy
  • Your Track: Top Gun raceway, Fallon Nv
  • Your Vehicle: 58 Chevy Apache 3100 truck
  • General Location: Reno, Nv
Re: I need your help- Magneto kill switch circuit
« Reply #5 on: February 21, 2020, 09:29:21 AM »
Lynn, I think your right, so no rocks for you.  Guys, I'll check out the relays. Thank for your replies. My truck is getting very close to be done. Thanks again everyone. 

Offline 58Apache

  • Newbie
  • *
  • Posts: 20
    • View Profile
  • Your Best Time: none
  • Your Engine: 572 Aluminum Keith Black Chevy
  • Your Track: Top Gun raceway, Fallon Nv
  • Your Vehicle: 58 Chevy Apache 3100 truck
  • General Location: Reno, Nv
Re: I need your help- Magneto kill switch circuit
« Reply #6 on: February 21, 2020, 03:42:16 PM »
I called FIE and talked to Spud- they have a relay designed just for this purpose. Thanks again for the help.