Author Topic: Rearend Upright Strap Thickness Requirement  (Read 5238 times)

Offline Countn Carbs

  • Jr. Member
  • **
  • Posts: 86
    • View Profile
  • Your Track: Bandimere Mo-Kan
  • Your Vehicle: 1931 Chevy Roadster
Rearend Upright Strap Thickness Requirement
« on: December 18, 2018, 08:32:48 AM »
What is the required thickness of the vertical straps in the mounting of a rearend?  Mine are 3/16" (purchased from a well-known chassis builder) and I had another chassis builder tell me over the weekend they need to be 1/4" minimum.
I've tried to locate the requirement in NHRA and SFI regs but I'm not having much luck and I could sure use some clarification.
« Last Edit: December 18, 2018, 08:40:41 AM by Countn Carbs »

Offline gregm784

  • Sr. Member
  • ****
  • Posts: 384
    • View Profile
    • Means Racing
  • Your Engine: 365" GenIV SBC
  • Your Track: Famoso Raceway
  • Your Vehicle: 1997 Stirling 200" FED
Re: Rearend Upright Strap Thickness Requirement
« Reply #1 on: December 18, 2018, 01:58:06 PM »
Money is very well spent on buying a set of SFI plans. 

Here's the part on rear ends

-----------------------------------------------------------------------------
IV. REAR END MOUNTING STANDARDS
1. UPRIGHTS
a. 1 1/4" x .083" tubing (#8) on each side of the chassis with either one
(1) 3/16" (4.7mm) SAE 4130N steel plate per side (no bosses
required) or two (2) 1/8" (3.2mm) SAE 4130N steel plates per side with
3/4" (19mm) minimum outside diameter bosses. Single plates must be
fully welded to the rear end uprights (#8) and to the upper (#4) and
lower (#16 & #17) frame rails on one side of each plate with 1/4"
(6.4mm) minimum wrap around the upper (#4) and lower (#16 & #17)
frame rails. The other side must be welded with one (1) inch (25.4mm)
minimum skip welds. Double plates must be fully welded to the rear
end uprights (#8) and to the upper (#4) and lower (#16 & #17) frame
rails on one side of each plate with 1/4" (6.4mm) minimum wrap
around the upper (#4) and lower (#16 & #17) frame rails.
b. 1 3/4" x 1" x .065" rectangular tubing (#8) on each side of the chassis
fully welded to the upper (#4) and lower (#16 & #17) frame rails with
one (1) inch (25.4mm) minimum diameter bosses fully welded into the
uprights (#8).

2. BOLTED DIRECT
The rear end housing must have one (1) 1/4" (6.4mm) SAE 4130N steel plate
welded on each side of the housing. The plates must be fully welded to the
housing and the plates and welds must wrap around the housing a minimum of
180°.

3. BOLTED INDIRECT
One (1) plate required on each side of the housing. The material may be either
1/4" (6.4mm) SAE 4130N steel or 3/8" (9.5mm) 6061-T6, 7075-T6 or 2024-T3
wrought heat treated aluminum alloy (no cast tooling plate).

4. FASTENERS-MINIMUM SPREAD DISTANCE-EDGE DISTANCE
For indirect mounting, all of the mounting fasteners, provided by the
manufacturer, must be used to attach the plates to the rear end/axle housing.
All plates must be bolted to the rear end uprights (#8) using at least four (4)
7/16" (11mm) SAE Grade 5 (Class 9.8) or better bolts with steel self locking nuts
on each side. The bolt hole minimum spread distance is five (5) inches (12.7cm),
measured from the centerlines of the outermost bolts. The minimum edge
distance for all plates (including the upright plates) is 1 1 /2 times the bolt
diameter, measured from the centerline of the bolt to the nearest edge.
-----------------------------------------------------------------------------

Greg
El Dorado County, CA
www.meansracing.com

Offline gregm784

  • Sr. Member
  • ****
  • Posts: 384
    • View Profile
    • Means Racing
  • Your Engine: 365" GenIV SBC
  • Your Track: Famoso Raceway
  • Your Vehicle: 1997 Stirling 200" FED
Re: Rearend Upright Strap Thickness Requirement
« Reply #2 on: December 18, 2018, 02:00:11 PM »
Same thing in a PDF you can download.
Greg
El Dorado County, CA
www.meansracing.com

Offline hemidakota

  • Full Member
  • ***
  • Posts: 210
    • View Profile
  • Your Best Time: 7.69 @ 173.5mph
  • Your Engine: 510 B1MC Wedge
  • Your Track: sacramento raceway
  • Your Vehicle: 02 200" fed
  • General Location: west coast
Re: Rearend Upright Strap Thickness Requirement
« Reply #3 on: December 18, 2018, 07:35:26 PM »
I agree with Greg M., the SFI book has so much more in it. Money well spent and all the information you will need. As I recall it only took two days to get the book also. Good luck and most of all Good Times.
Greg S.
If it jams force it, if it breaks it needed replaced anyways

Offline George

  • Hero Member
  • *****
  • Posts: 518
    • View Profile
  • Your Vehicle: 1964 Mercury Comet Super Stock/ M automatic
  • General Location: Midwest USA
Re: Rearend Upright Strap Thickness Requirement
« Reply #4 on: December 19, 2018, 04:00:58 AM »
Buy into the SFI.                                  https://sfifoundation.com/

Offline Countn Carbs

  • Jr. Member
  • **
  • Posts: 86
    • View Profile
  • Your Track: Bandimere Mo-Kan
  • Your Vehicle: 1931 Chevy Roadster
Re: Rearend Upright Strap Thickness Requirement
« Reply #5 on: December 19, 2018, 06:51:53 AM »
Thank you guys.  I appreciate all the help and information.  Point taken on ordering the SFI specs and I will certainly do that.  Thank you again.

Offline rooman

  • Moderator
  • Hero Member
  • *****
  • Posts: 559
    • View Profile
  • Your Best Time: 6.200/222.05 (1/4 mile--NT/F)
Re: Rearend Upright Strap Thickness Requirement
« Reply #6 on: December 19, 2018, 08:37:56 AM »
Regarding this part of the spec: " Single plates must be
fully welded to the rear end uprights (#8) and to the upper (#4) and
lower (#16 & #17) frame rails on one side of each plate with 1/4"
(6.4mm) minimum wrap around the upper (#4) and lower (#16 & #17)
frame rails. The other side must be welded with one (1) inch (25.4mm)
minimum skip welds. Double plates must be fully welded to the rear
end uprights (#8) and to the upper (#4) and lower (#16 & #17) frame
rails on one side of each plate with 1/4" (6.4mm) minimum wrap
around the upper (#4) and lower (#16 & #17) frame rails."   the 1/4" wrap refers to the weld and not the mounting plate. That may sound pretty basic but I know of an instance of an NHRA tech inspector telling a builder that the plate had to be wrapped around the tube. As Larry Morgan noted in one of his clashes with the NHRA, "You can't fix stupid"

Roo
Yeah, I am from the south--any further south and I would have been a bloody penguin.

Offline THE FRENCHTOWN FLYER

  • Sr. Member
  • ****
  • Posts: 360
    • View Profile
  • Your Best Time: 8.28@168 door; 9.00@147 6-cyl alt; 8.53@160 RED
  • Your Engine: 300 Ford six NA w/ crossflow and prod. heads
  • Your Track: Milan, Thompson
  • Your Vehicle: (3) Advanced Chassis altered , The Last Logghe altered, '30 RPU
  • General Location: North Coast
Re: Rearend Upright Strap Thickness Requirement
« Reply #7 on: December 19, 2018, 08:48:00 AM »
Countin,

I see by your avatar car you are constructing a FED with a vintage inline six. While the SFI spec may call out 1/4" 4130 plates I think that in your specific case you could logically argue that the the 3/16" plates will more than suffice for the power you are capable of transmitting to the rear end. A good alternative to cutting off the existing plates and welding new - which would induce warpage into the rear housing - might be to weld localized reinforcements (i.e., washers)around the plate mounting holes. If at such time as you decide to install a blown hemi you could consider a further upgrade to the housing.

I'd feel perfectly safe with 3/16" plates.

Offline Countn Carbs

  • Jr. Member
  • **
  • Posts: 86
    • View Profile
  • Your Track: Bandimere Mo-Kan
  • Your Vehicle: 1931 Chevy Roadster
Re: Rearend Upright Strap Thickness Requirement
« Reply #8 on: December 19, 2018, 11:16:04 AM »
Regarding this part of the spec: " Single plates must be
fully welded to the rear end uprights (#8) and to the upper (#4) and
lower (#16 & #17) frame rails on one side of each plate with 1/4"
(6.4mm) minimum wrap around the upper (#4) and lower (#16 & #17)
frame rails. The other side must be welded with one (1) inch (25.4mm)
minimum skip welds. Double plates must be fully welded to the rear
end uprights (#8) and to the upper (#4) and lower (#16 & #17) frame
rails on one side of each plate with 1/4" (6.4mm) minimum wrap
around the upper (#4) and lower (#16 & #17) frame rails."   the 1/4" wrap refers to the weld and not the mounting plate. That may sound pretty basic but I know of an instance of an NHRA tech inspector telling a builder that the plate had to be wrapped around the tube. As Larry Morgan noted in one of his clashes with the NHRA, "You can't fix stupid"


Roo


Thanks Roo - this section did actually cause some confusion when I read that..

Offline Countn Carbs

  • Jr. Member
  • **
  • Posts: 86
    • View Profile
  • Your Track: Bandimere Mo-Kan
  • Your Vehicle: 1931 Chevy Roadster
Re: Rearend Upright Strap Thickness Requirement
« Reply #9 on: December 19, 2018, 11:22:46 AM »
Countin,

I see by your avatar car you are constructing a FED with a vintage inline six. While the SFI spec may call out 1/4" 4130 plates I think that in your specific case you could logically argue that the the 3/16" plates will more than suffice for the power you are capable of transmitting to the rear end. A good alternative to cutting off the existing plates and welding new - which would induce warpage into the rear housing - might be to weld localized reinforcements (i.e., washers)around the plate mounting holes. If at such time as you decide to install a blown hemi you could consider a further upgrade to the housing.

I'd feel perfectly safe with 3/16" plates.


Thanks FF - yeah the rearend plates are indeed 1/4" - it's the uprights that are 3/16" so it looks/reads like we're good.  Yeah you're right...just a little inline 6 with not much power but plan to run it monthly in our Vintage Drag Racing club.
Also - great article you wrote in this months 12 Port News!!  Looks like an awesome little project and looking forward to seeing more about it in future issues.

Offline fuel749

  • Full Member
  • ***
  • Posts: 159
    • View Profile
    • Dragster Supply
  • Your Track: New England Dragway
  • Your Vehicle: FED/Altered
Re: Rearend Upright Strap Thickness Requirement
« Reply #10 on: December 20, 2018, 01:08:59 PM »
Just so no one gets confused if they happen to find out their rear end uprights aren't .083 wall, the spec Greg quoted is the faster 2.2 spec (5.99 and quicker).  The 2.4 spec (6.00-7.49) calls for a minimum .058 upright.

Offline THE FRENCHTOWN FLYER

  • Sr. Member
  • ****
  • Posts: 360
    • View Profile
  • Your Best Time: 8.28@168 door; 9.00@147 6-cyl alt; 8.53@160 RED
  • Your Engine: 300 Ford six NA w/ crossflow and prod. heads
  • Your Track: Milan, Thompson
  • Your Vehicle: (3) Advanced Chassis altered , The Last Logghe altered, '30 RPU
  • General Location: North Coast
Re: Rearend Upright Strap Thickness Requirement
« Reply #11 on: December 20, 2018, 01:36:45 PM »

Thanks FF - yeah the rearend plates are indeed 1/4" - it's the uprights that are 3/16" so it looks/reads like we're good.  Yeah you're right...just a little inline 6 with not much power but plan to run it monthly in our Vintage Drag Racing club.
Also - great article you wrote in this months 12 Port News!!  Looks like an awesome little project and looking forward to seeing more about it in future issues.

My bad - I thought you meant the plates on the axle itself. Nevertheless I'd say you're good.

Thanks for the kudos. Stay tuned for the second article in the series of four.

Offline gregm784

  • Sr. Member
  • ****
  • Posts: 384
    • View Profile
    • Means Racing
  • Your Engine: 365" GenIV SBC
  • Your Track: Famoso Raceway
  • Your Vehicle: 1997 Stirling 200" FED
Re: Rearend Upright Strap Thickness Requirement
« Reply #12 on: December 20, 2018, 04:01:15 PM »
Just so no one gets confused if they happen to find out their rear end uprights aren't .083 wall, the spec Greg quoted is the faster 2.2 spec (5.99 and quicker).  The 2.4 spec (6.00-7.49) calls for a minimum .058 upright.

Oops, i meant to include that in my message. thank you. 

Yes, that is for 2.4C - Top Fuel.
Greg
El Dorado County, CA
www.meansracing.com

Offline fuel749

  • Full Member
  • ***
  • Posts: 159
    • View Profile
    • Dragster Supply
  • Your Track: New England Dragway
  • Your Vehicle: FED/Altered
Re: Rearend Upright Strap Thickness Requirement
« Reply #13 on: December 21, 2018, 11:48:26 AM »
Just so no one gets confused if they happen to find out their rear end uprights aren't .083 wall, the spec Greg quoted is the faster 2.2 spec (5.99 and quicker).  The 2.4 spec (6.00-7.49) calls for a minimum .058 upright.

Oops, i meant to include that in my message. thank you. 

Yes, that is for 2.4C - Top Fuel.

I won't bash you to hard since the computer I'm typing this on is the one you built me.