Author Topic: Misbehaving plug wires  (Read 3475 times)

Offline Spud Miller

  • Global Moderator
  • Sr. Member
  • *****
  • Posts: 332
    • View Profile
    • Fuel Injection Ent., LLC
Misbehaving plug wires
« on: July 30, 2018, 09:44:12 AM »
 Since someone brought it up in another thread...I have MANY Promag "bad plug wire" stories this season so far.

 Behavior that you'd never suspect and it's the suppression core race wire that the electronic mags require. People don't understand that it wears out! It looks perfectly fine and good but electrically, it's a nightmare. It might check out fine and seem normal with the ohm meter, but when they're changed out for a new set, everything is happy and normal again. Even if you can't explain why, it's difficult to argue with results!

 So, if your Promag ends up having strange timing and phasing issues that don't make sense, timing lights freaking out, points boxes not working right...save yourself some time and change the plug wires first!

 Spud

Fuel Injection Enterprises, LLC
     Mechanical Injection
     Magnetos
     EFI Conversions

Offline 32bantam

  • Full Member
  • ***
  • Posts: 117
    • View Profile
    • SS3 Race Team
  • Your Best Time: 6.87 at BG 2013 aiming for 7.0
  • Your Track: Empire Dragway, NY
  • Your Vehicle: 32 Bantam altered
Re: Misbehaving plug wires
« Reply #1 on: July 31, 2018, 04:44:16 AM »
AMEN !!!!!!!!!!  Just went thru that with Gary O Connells car !!!!!

Steve Walczak

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1910
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: Misbehaving plug wires
« Reply #2 on: July 31, 2018, 09:43:13 AM »
Guessing noway to check other than swap out. Sucks because normally one wire bad,plus I have 4 or 5 old sets.Not that anything was wrong with them,just maintenance swaps.   OP said super mag issue and figuring same thing with MSD mags.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline Spud Miller

  • Global Moderator
  • Sr. Member
  • *****
  • Posts: 332
    • View Profile
    • Fuel Injection Ent., LLC
Re: Misbehaving plug wires
« Reply #3 on: July 31, 2018, 09:51:52 AM »

 Nope this isn't a Super-mag issue...this is only with Pro-mags. They are VERY sensitive to bad or overused wires due to the solid state components in the points box.

 In the situations referred to, the wires tested good. But they were the problem.

 Spud

Fuel Injection Enterprises, LLC
     Mechanical Injection
     Magnetos
     EFI Conversions

Offline Paul New

  • Hero Member
  • *****
  • Posts: 745
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: Misbehaving plug wires
« Reply #4 on: July 31, 2018, 11:51:03 AM »
I wonder if a Insulation Megger would find the insulation bad and show something?

Offline Spud Miller

  • Global Moderator
  • Sr. Member
  • *****
  • Posts: 332
    • View Profile
    • Fuel Injection Ent., LLC
Re: Misbehaving plug wires
« Reply #5 on: July 31, 2018, 12:01:04 PM »

 The insulation isn't bad...it isn't shorting out anywhere. There aren't any dropped cylinders, instead it messes with timing in a big way which is a delay function and related to the smarts in the points box. And it isn't just a timing light phenomena in the pits...the cars really RUN BAD. So the timing strangeness is real. It's a mystery.

 Spud

Fuel Injection Enterprises, LLC
     Mechanical Injection
     Magnetos
     EFI Conversions

Offline Paul New

  • Hero Member
  • *****
  • Posts: 745
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: Misbehaving plug wires
« Reply #6 on: July 31, 2018, 01:03:19 PM »
Interesting?  There would have to be some sort of test I would think?

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1910
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: Misbehaving plug wires
« Reply #7 on: July 31, 2018, 02:39:46 PM »
My bad on pro mag part/ So I guess I  might as well add new wires to list of need to have now. Running out of lines,going to have to flip paper over.LOL
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1910
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: Misbehaving plug wires
« Reply #8 on: July 31, 2018, 02:42:09 PM »
Is this just a issue lately.Like maybe something in manufacturing of wire? Asking Because I have cpl sets on shelf that are old but never used and wondering if should use those or just buy all new.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline gregm784

  • Sr. Member
  • ****
  • Posts: 384
    • View Profile
    • Means Racing
  • Your Engine: 365" GenIV SBC
  • Your Track: Famoso Raceway
  • Your Vehicle: 1997 Stirling 200" FED
Re: Misbehaving plug wires
« Reply #9 on: July 31, 2018, 02:57:01 PM »
Is this why you started selling the Taylor wire Spud? i still have a couple sets of new MSD wires.  Should i be switching to Taylor?
Greg
El Dorado County, CA
www.meansracing.com

Offline Spud Miller

  • Global Moderator
  • Sr. Member
  • *****
  • Posts: 332
    • View Profile
    • Fuel Injection Ent., LLC
Re: Misbehaving plug wires
« Reply #10 on: August 01, 2018, 09:51:43 AM »

 I'd never seen these types of problems before a few months ago, but it could be a change in the points boxes too. Every one of these cases was indeed with MSD wire, but I have no reason to believe it couldn't be a problem with other brands of similar wire. All brands of suppression core wire wear out with use eventually.

 There were quite a few reasons for us switching to Taylor wire, but probably none of which would be the culprit in this case.

 I wouldn't be a bit afraid to use your brand new sets of MSD wire.

 Spud

Fuel Injection Enterprises, LLC
     Mechanical Injection
     Magnetos
     EFI Conversions