Author Topic: Rear Wheel Torque  (Read 3660 times)

Offline spitzerscott

  • Full Member
  • ***
  • Posts: 115
    • View Profile
    • Ogg Motorsports
  • Your Best Time: 5.73@118.80
  • Your Engine: 336 Small Block Chevy
  • Your Track: Osceola IN, Top Eliminator runs 1/8 mile
  • Your Vehicle: Spitzer225 RED, Alcohol SBC
  • General Location: Northern Indiana
Rear Wheel Torque
« on: January 08, 2018, 03:25:17 PM »
I have 5/8-18 rear studs, what is the proper torque spec?  Weld wheels.  Thanks,  Scott

Offline dusterdave173

  • Hero Member
  • *****
  • Posts: 638
    • View Profile
  • Your Best Time: 5.38in 1/8th
  • Your Engine: 355 CI SBC
  • Your Track: Mooresville, NC
  • Your Vehicle: CenPen 200 inch FED
Re: Rear Wheel Torque
« Reply #1 on: January 09, 2018, 03:51:12 AM »
I find that with aluminum ( or mag) wheels and the aluminum spacers over the studs that it becomes a game of feel
Those aluminum spacers have to "compact' then things start to get tight--issues are compounded by the fact that many of the lug nuts have serrations on the back side that chew away at the aluminum spacers 
So my advice is to tighten them up until you feel all of the slack is out and that things are "compressed" then use TQ wrench to just ensure they are all the same--I don't use a TQ wrench--The way that the hats and rotors are-- there is not an issue with rotor warp to worry about so...
The TQ value for a stud that big would be a lot so be careful
I have always had a fascination with fast cars at the expense of more normal character development

Offline JrFuel Hayden

  • Hero Member
  • *****
  • Posts: 600
    • View Profile
    • Hayden Enterprises Speciality Wheels
  • Your Best Time: 6.02, 236 mph, 1/4 in 1973 Div 3 TF Champ
  • Your Engine: SBC, Alky, 403 ci, Best 6.99 @ 190 & 409 Hemi
  • Your Track: Bakersfield
  • Your Vehicle: 225" FED NHRA Heritage Jr Fuel
Re: Rear Wheel Torque
« Reply #2 on: January 09, 2018, 03:22:49 PM »
My 5/8" tie studs we torque at 85 #, our old studs 1/2" we ran at 80 #, both with alum lug nuts.
Hope this helps.
Jon
Jon C. Hansen

Hayden Wheels

Offline hemidakota

  • Full Member
  • ***
  • Posts: 210
    • View Profile
  • Your Best Time: 7.69 @ 173.5mph
  • Your Engine: 510 B1MC Wedge
  • Your Track: sacramento raceway
  • Your Vehicle: 02 200" fed
  • General Location: west coast
Re: Rear Wheel Torque
« Reply #3 on: January 09, 2018, 06:59:40 PM »
Weld Wheels web site


Lug Nuts: 7/16 Wheel stud = 75-85 ft-lbs
1/2 Wheel stud = 85-95 ft-lbs
5/8 Wheel stud = 130-140 ft-lbs
12mm = 90 ft-lbs 14mm = 110 ft-lbs

Weld Racing does not recommend the use of lubricant when installing lug nuts.

Strange also recommends 130 with the aluminum spacers...

If it jams force it, if it breaks it needed replaced anyways

Offline Paul New

  • Hero Member
  • *****
  • Posts: 745
    • View Profile
  • Your Best Time: 6.47 @ 214 MPH SBC
  • Your Engine: 387" SBC
  • Your Track: Woodburn Dragstrip
  • Your Vehicle: 2005 FED
Re: Rear Wheel Torque
« Reply #4 on: January 09, 2018, 07:06:18 PM »
We torque ours at 115lbs not sure where we came up with that number but that’s what we have used for years