Author Topic: Zoomies vs collector headers  (Read 24879 times)

Offline hemidakota

  • Full Member
  • ***
  • Posts: 210
    • View Profile
  • Your Best Time: 7.69 @ 173.5mph
  • Your Engine: 510 B1MC Wedge
  • Your Track: sacramento raceway
  • Your Vehicle: 02 200" fed
  • General Location: west coast
Re: Zoomies vs collector headers
« Reply #30 on: September 14, 2017, 12:35:15 PM »
I have played the zoomie vs header on a 565bbc in a fed. The biggest difference was the tune up. Headers required quite a bit more fuel and made a ton more power down low. I would say headers make more power but too many changes needed to be made to get good results. Had to leave at a much lower rpm also or would just blow the slicks off at the hit with the headers. Was fun to do.
If it jams force it, if it breaks it needed replaced anyways

Offline JrFuel Hayden

  • Hero Member
  • *****
  • Posts: 600
    • View Profile
    • Hayden Enterprises Speciality Wheels
  • Your Best Time: 6.02, 236 mph, 1/4 in 1973 Div 3 TF Champ
  • Your Engine: SBC, Alky, 403 ci, Best 6.99 @ 190 & 409 Hemi
  • Your Track: Bakersfield
  • Your Vehicle: 225" FED NHRA Heritage Jr Fuel
Re: Zoomies vs collector headers
« Reply #31 on: September 14, 2017, 05:15:49 PM »
On Gas or Alky, and what RPM did you shift at ?
Jon
Jon C. Hansen

Hayden Wheels

Offline hemidakota

  • Full Member
  • ***
  • Posts: 210
    • View Profile
  • Your Best Time: 7.69 @ 173.5mph
  • Your Engine: 510 B1MC Wedge
  • Your Track: sacramento raceway
  • Your Vehicle: 02 200" fed
  • General Location: west coast
Re: Zoomies vs collector headers
« Reply #32 on: September 15, 2017, 07:07:28 AM »
injected alky shift 7500 rpm, thru traps at 7800.
If it jams force it, if it breaks it needed replaced anyways

Offline Roger

  • Full Member
  • ***
  • Posts: 185
    • View Profile
  • Your Vehicle: 125 inch Altered
Re: Zoomies vs collector headers
« Reply #33 on: September 15, 2017, 09:20:55 AM »
Was there much difference in MPH?

Offline JrFuel Hayden

  • Hero Member
  • *****
  • Posts: 600
    • View Profile
    • Hayden Enterprises Speciality Wheels
  • Your Best Time: 6.02, 236 mph, 1/4 in 1973 Div 3 TF Champ
  • Your Engine: SBC, Alky, 403 ci, Best 6.99 @ 190 & 409 Hemi
  • Your Track: Bakersfield
  • Your Vehicle: 225" FED NHRA Heritage Jr Fuel
Re: Zoomies vs collector headers
« Reply #34 on: September 15, 2017, 04:00:41 PM »
not a surprize theory goes long pipes and injector stacks is for bottom end power, shorter good for higher RPM power. Matter-a-fact I have suggested to some racers to put their short stacks on when they are at a bad traction track, because it will take some bottom power away.
Jon C. Hansen

Hayden Wheels

Offline hemidakota

  • Full Member
  • ***
  • Posts: 210
    • View Profile
  • Your Best Time: 7.69 @ 173.5mph
  • Your Engine: 510 B1MC Wedge
  • Your Track: sacramento raceway
  • Your Vehicle: 02 200" fed
  • General Location: west coast
Re: Zoomies vs collector headers
« Reply #35 on: September 19, 2017, 06:09:27 PM »
MPH was the same that day, but I don't think the tune where it needed to be, was still a little lean. Just got it close on the last pass. 60' was better by .05 and it picked up 3 mph on the last jet change. There was just not enough time to make enough changes to get it happy.
If it jams force it, if it breaks it needed replaced anyways

Offline Roger

  • Full Member
  • ***
  • Posts: 185
    • View Profile
  • Your Vehicle: 125 inch Altered
Re: Zoomies vs collector headers
« Reply #36 on: September 22, 2017, 11:18:30 AM »
The reason I asked about the MPH was because of some other pieces of anecdotal information I’ve seen on some other web sites, including the performance boat sites. They tend to indicate the same things you voiced; bottom end torque takes a bad hit with zoomies but the top-end power doesn’t seem to be affected. Their words:

“1984 UGF back to back runs: 129.31 headers & injectors (staggered tubes), 130.81 Bassett Zoomies 2-1/4. No other changes.”

“Our Unblown Gas Boat has a 555 Chevy… was man-handling our drag boat out of the gate. The boat came out so hard that it was out of control…installed a set of zoomies and a prop…the boat now leaves the gate under control…was almost 4 tenths better than we have ever ran…pulling about 8300rpm in the lights.”

“Had the same deal on one of my hydro engines. Collector made more on the dyno, zoomies faster in the boat. I wasn't racing a dyno so I ran the zoomies.”

The Stahl Headers Newsletter this thread was based on made mention that zoomies ran “quite well from 3500 to 4500 and from 7000 to 7500.” Your experience and the ones I found seem to indicate that once you’re into that 7000-7500rpm range the zoomies may have little effect on top end performance, just as stated in the newsletter. That leaves the 5500-6500rpm range where Stahl says that the performance on a 406” SBC will see “as much as 45 to 50 HP difference between 5500 and 6500.” The 383” SBC engine I’m assembling now will operate in that 5500-7000rpm range to run the 8.5 quarter index and the 5.50 eighth index. Should be interesting, will run the tests again next year with the new engine and will post the results.

Roger

Offline PSweeney

  • Full Member
  • ***
  • Posts: 231
    • View Profile
  • Your Track: Santa Pod
  • Your Vehicle: 138in SBC slingshot
Re: Zoomies vs collector headers
« Reply #37 on: October 02, 2017, 03:19:16 AM »
I've also tested zoomies and headers before.  There is no one single theory as there are so many contributing factors from car to car.  Headers came out marginally better for the engine I was running, but no amount of power increase would make me run them on a digger again, just looks plain wrong.

Offline Guido

  • Newbie
  • *
  • Posts: 32
    • View Profile
  • Your Best Time: 7.52 185 mph
  • Your Engine: Supercharged sbc
  • Your Track: Kearney raceway park
  • Your Vehicle: 170" FED
  • General Location: Mid westMHRUWX
Re: Zoomies vs collector headers
« Reply #38 on: October 13, 2017, 08:13:07 AM »
There's allot of great info on this thread! I am running a sbc with a small blower and was wondering about what size of tubing, I have 2" that are approximately 16" from the flange to the tip. Would a 1 5/8 or 1 3/4 work better?

Offline JrFuel Hayden

  • Hero Member
  • *****
  • Posts: 600
    • View Profile
    • Hayden Enterprises Speciality Wheels
  • Your Best Time: 6.02, 236 mph, 1/4 in 1973 Div 3 TF Champ
  • Your Engine: SBC, Alky, 403 ci, Best 6.99 @ 190 & 409 Hemi
  • Your Track: Bakersfield
  • Your Vehicle: 225" FED NHRA Heritage Jr Fuel
Re: Zoomies vs collector headers
« Reply #39 on: October 13, 2017, 05:26:56 PM »
If you were not runing a blower the tubing size would make a difference depending on head air flow and RPM, however since a blower doesn't need exhaust tuning, so keep the 2" and spend your money and time on something else to make your combo better. One thing I would look at is your converter, so many racers I know have said the biggest improvement in performance was their converter change.
The goal should to better match your stall to your engine power curve. If your cam/motor comes on at 6,000 rpm, and you have stall of 4,000 rpm, guess what will happen.
I've had great returns on ET using A-1 Converters in WA. 360-574-9966.
BTW I run 2 1/8" zoomies aimed at the top of my slicks [ layed-back] on my all iron 23° raised runner injected alky Heritage JF, good for 9800-10,000 rpm, running low 7.0's, 188-190 mph.

Have Fun
Jon
Jon C. Hansen

Hayden Wheels

Offline Roger

  • Full Member
  • ***
  • Posts: 185
    • View Profile
  • Your Vehicle: 125 inch Altered
Re: Zoomies vs collector headers
« Reply #40 on: October 13, 2017, 06:01:18 PM »
Listen to Jon. A blower engine is a whole different critter than a N/A engine when it comes to exhaust.

Offline Guido

  • Newbie
  • *
  • Posts: 32
    • View Profile
  • Your Best Time: 7.52 185 mph
  • Your Engine: Supercharged sbc
  • Your Track: Kearney raceway park
  • Your Vehicle: 170" FED
  • General Location: Mid westMHRUWX
Re: Zoomies vs collector headers
« Reply #41 on: October 17, 2017, 04:36:35 PM »
Thanks for the info,  this is my first experience in a FED I just made my first few passes in it and am hooked! What a blast

Offline THE FRENCHTOWN FLYER

  • Sr. Member
  • ****
  • Posts: 360
    • View Profile
  • Your Best Time: 8.28@168 door; 9.00@147 6-cyl alt; 8.53@160 RED
  • Your Engine: 300 Ford six NA w/ crossflow and prod. heads
  • Your Track: Milan, Thompson
  • Your Vehicle: (3) Advanced Chassis altered , The Last Logghe altered, '30 RPU
  • General Location: North Coast
Re: Zoomies vs collector headers
« Reply #42 on: October 18, 2017, 09:15:54 AM »
Pretty car.
Clean.
Simple.

Offline George

  • Hero Member
  • *****
  • Posts: 518
    • View Profile
  • Your Vehicle: 1964 Mercury Comet Super Stock/ M automatic
  • General Location: Midwest USA
Re: Zoomies vs collector headers
« Reply #43 on: October 19, 2017, 02:11:04 AM »
I've also tested zoomies and headers before.  There is no one single theory as there are so many contributing factors from car to car.  Headers came out marginally better for the engine I was running, but no amount of power increase would make me run them on a digger again, just looks plain wrong.


Totally agree on the looks. Collector headers on a front engine car ruin the look for me.