Author Topic: wheels, screws and liners  (Read 6035 times)

Offline tdracer

  • Newbie
  • *
  • Posts: 17
    • View Profile
  • Your Best Time: 6.90 1/4 (RED) 4.71 1/8 (FED)
  • Your Engine: SBC Supercharged alky 400cid
  • Your Track: Various
  • Your Vehicle: Dragsters front and rear engined
wheels, screws and liners
« on: June 23, 2016, 01:24:56 PM »
I am looking at taking the Beadlocks and wide tires off my FED.

I want to use a old style slotted mag(Ansen?) and a smaller 11.5 or 12" wide tire.  My concern is the wheel rotating on the tire.  The car 60' foots in the 1.0's, its just over 1800lbs.

I don't want to use rim screws, is their an inner liner available that i could use? (15" diameter wheels).

Should i just go tubeless and not worry about it?

Any other idea's?

Thanks

dreracecar

  • Guest
Re: wheels, screws and liners
« Reply #1 on: June 23, 2016, 03:04:36 PM »
generally machined aluminum wheels hold the tire better then the spun rims along with higher air pressure new tire design likes now. Since you are running tubeless, spinning the tube and ripping out the fill valve has been eliminated, you can experiment running without screws, just paint a witness line from the tire to the wheel rim and check for movement.
Ran cast wheels for years with just 5 screws per side w/ 1650# car running 7.0's  also I prefer to run a 10" wheel for a 12"  wide tire as it squares up on the burnout and evenly heats up the tire and contact patch on the track

Offline digster

  • Jr. Member
  • **
  • Posts: 89
    • View Profile
  • Your Best Time: 8.01 1/4
  • Your Engine: Hilborn Injected 427 SBC (Methanol)
  • Your Track: Top End Raceways, Sabin Mn
  • Your Vehicle: 1970 190 inch FED
Re: wheels, screws and liners
« Reply #2 on: June 23, 2016, 03:41:00 PM »
 If you decide to try screwless be sure to mount without tire soap or bead grease.
Some door car racers in my area use Aquanet hairspray for bead seating and no screws.

Offline tdracer

  • Newbie
  • *
  • Posts: 17
    • View Profile
  • Your Best Time: 6.90 1/4 (RED) 4.71 1/8 (FED)
  • Your Engine: SBC Supercharged alky 400cid
  • Your Track: Various
  • Your Vehicle: Dragsters front and rear engined
Re: wheels, screws and liners
« Reply #3 on: June 24, 2016, 07:00:27 AM »
Thanks for the replies, i think maybe going with the 5 screws just to be on the safer side might be the plan.

I'll keep researching liners to see if that's an option.

Thanks


dreracecar

  • Guest
Re: wheels, screws and liners
« Reply #4 on: June 24, 2016, 08:40:12 AM »
since the intro of beadlocks, tire companys are not making liners that much except for nascar and Hoosier makes a 16" for big tires, 
Expence-weight-and the chance of pressure equalizing (and blowing out the tire gauge--opps) are the things that steer me away from them at our level

Offline tdracer

  • Newbie
  • *
  • Posts: 17
    • View Profile
  • Your Best Time: 6.90 1/4 (RED) 4.71 1/8 (FED)
  • Your Engine: SBC Supercharged alky 400cid
  • Your Track: Various
  • Your Vehicle: Dragsters front and rear engined
Re: wheels, screws and liners
« Reply #5 on: June 24, 2016, 10:16:22 AM »
I hear some radial guys are gluing tires to the wheels, any idea what they are using?

Maybe try glue and mark the tire?

Thinking in "nostalgia mode" i should just soften the launch anyway.

Brian

dreracecar

  • Guest
Re: wheels, screws and liners
« Reply #6 on: June 24, 2016, 11:18:04 AM »
I have never used the tranny brake to launch my car, only the hand brake at high idle--- Its what works for me

Offline StigO

  • Newbie
  • *
  • Posts: 11
    • View Profile
  • Your Best Time: 6,48/210 1/4 mile
  • Your Engine: Gray DRCE3 500"
  • Your Track: Tierp Arena Sweden
  • Your Vehicle: Neil&Parks FED
Re: wheels, screws and liners
« Reply #7 on: June 24, 2016, 03:00:49 PM »
Did use Tip Top Remaxx anti gliss  for many years to glue tire to rim and never had any problem with it.

Offline PSweeney

  • Full Member
  • ***
  • Posts: 231
    • View Profile
  • Your Track: Santa Pod
  • Your Vehicle: 138in SBC slingshot
Re: wheels, screws and liners
« Reply #8 on: June 27, 2016, 05:44:10 AM »
some use Permantex  . I have the same dilemma, but I think I will run without screws and watch it along.