« previous next »
Pages: [1]   Go Down

Author Topic: cam belt drive  (Read 4917 times)

Offline hemidakota

  • Full Member
  • ***
  • Posts: 210
    • View Profile
  • Your Best Time: 7.69 @ 173.5mph
  • Your Engine: 510 B1MC Wedge
  • Your Track: sacramento raceway
  • Your Vehicle: 02 200" fed
  • General Location: west coast
cam belt drive
« on: August 13, 2015, 07:00:45 AM »
So harmonics have been discussed. Is there any advantage to a belt drive rather than the ease of adjustment?
Logged
If it jams force it, if it breaks it needed replaced anyways

Offline Frontenginedragsters

  • Full Member
  • ***
  • Posts: 202
    • View Profile
    • Pro-Formance Specialties
Re: cam belt drive
« Reply #1 on: August 13, 2015, 07:43:18 AM »
The belt drive vs timing chain vs gear drive discussion will live on forever.
Every Comp Eliminator car and Pro Stock engine has a belt drive. Can't argue with High End technology.
I put a gear drive on everything I can, but only good quality. Lots of junk on the market.
I run almost every engine on our dyno before sending them out.
I'v seen timing retard with the lower cost belt drives. [Some company's should just stick to camshafts]
Ease of adjustment is great on the dyno for testing.

Just my thoughts: Matt
Logged
Driving a Front Engine Dragster builds character and keeps you awake for a 1/4 mile at a time.
http://www.pro-formancespecialties.com/

dreracecar

  • Guest
Re: cam belt drive
« Reply #2 on: August 13, 2015, 08:23:12 AM »
Here is my thoughts----
Chains are for bicycles
Belts are OK if you plan regulating engine temp to a constant and tension the belt accordingly, if not then the gear gives room for expansion as the engine heats up. I set my blower belt tension by idler slippage and after the run it is tighter.

All in all, "harmonics"  at our level is not an issue, but some members on this board can sure"pick the fly xxxx out of the pepper". Been running and a top competitor for over 20 years BUILD IT - TUNE IT - RUN IT
« Last Edit: August 13, 2015, 11:03:20 AM by dreracecar »
Logged

Offline masracingtd1167

  • Hero Member
  • *****
  • Posts: 1138
  • bill masiello Shelton Ct.
    • View Profile
  • Your Best Time: 7.40's at 181 on motor 6.94 at 192 nitrous
  • Your Engine: 394 chevy
  • Your Track: Lebanon Valley Dragway
  • Your Vehicle: 2003 Neil and Parks
Re: cam belt drive
« Reply #3 on: August 13, 2015, 02:08:50 PM »
I have never been a big fan of chains . I broke one once and it was a disaster . I ran a Summers gear drive for may years without a single problem . Today I run a Jessel belt drive and it works very well and very easy to make valve timing changes . If you are running a lot of lift and big springs I would say yes to the belt drive . Bill   
Logged

dreracecar

  • Guest
Re: cam belt drive
« Reply #4 on: August 13, 2015, 02:26:42 PM »
Maybe its just me, but I have never gone to a race with the thought of ever having to change my cam timing from where I set it when I built the engine.
Logged

Offline masracingtd1167

  • Hero Member
  • *****
  • Posts: 1138
  • bill masiello Shelton Ct.
    • View Profile
  • Your Best Time: 7.40's at 181 on motor 6.94 at 192 nitrous
  • Your Engine: 394 chevy
  • Your Track: Lebanon Valley Dragway
  • Your Vehicle: 2003 Neil and Parks
Re: cam belt drive
« Reply #5 on: August 13, 2015, 02:40:19 PM »
I have !
Logged

Offline ricardo1967

  • Hero Member
  • *****
  • Posts: 578
    • View Profile
  • Your Best Time: No full pass yet.
  • Your Engine: Alky SBC 400
  • Your Track: Brown County Dragway (Bean Blossom, IN)
  • Your Vehicle: 173" FED
Re: cam belt drive
« Reply #6 on: August 13, 2015, 03:41:18 PM »
I think that given the short runs harmonics aren't so harmful to a drag engine. Just my opinion.

The Jesel belt drive saved my bacon because in my engine the piston-to-valve clearance was less than desirable and the belt drive allowed me to "split the difference" and keep my current parts. I'll confess I also like its cool looks.
Logged
Pages: [1]   Go Up
« previous next »