« previous next »
Pages: [1]   Go Down

Author Topic: repair for PG case  (Read 6940 times)

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
repair for PG case
« on: April 23, 2015, 02:37:57 PM »
Have a local guy who had a case bored for roller bearing for output . Seems who ever did id either let it move or did not indicate it correctly. Shaft is off center,easy to see whnn tial housing is on and its short shaft.Has to be more than I measured .015 off center or .030 more towards top.

He want me to bore it out,insert sleeve,weld and bore to fit bearing. I would rather just weld it up and remachine.Either way there is very little material left to work with. Told him I would check and see what few others thought would be best repair.Ok best would be new case.         
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline bikeguy307

  • Full Member
  • ***
  • Posts: 241
    • View Profile
Re: repair for PG case
« Reply #1 on: April 23, 2015, 04:50:08 PM »
Is it an after market or stock case? Not sure I would spend time trying to save a stock. Now the cost of a after market would lead me to give it a try. I would rebore it to center press in a solid slug and bore for a bearing. I would avoid welding for fear of case warping.
« Last Edit: April 23, 2015, 05:20:21 PM by bikeguy307 »
Logged

Offline dusterdave173

  • Hero Member
  • *****
  • Posts: 638
    • View Profile
  • Your Best Time: 5.38in 1/8th
  • Your Engine: 355 CI SBC
  • Your Track: Mooresville, NC
  • Your Vehicle: CenPen 200 inch FED
Re: repair for PG case
« Reply #2 on: April 23, 2015, 05:17:30 PM »
Can't you just buy that rear support with a roller bearing in it and bolt it on? I am learning about Glides
Logged
I have always had a fascination with fast cars at the expense of more normal character development

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: repair for PG case
« Reply #3 on: April 23, 2015, 06:12:17 PM »
Dave rear support has bearing but case normally has bushing thats can be replaced with bearing also. Might go the soile piece and bore to fit.Guess I could actually get it bored in ball park on lathe leaving .150 to bore once it.

  Was worried about warpping with thinness of case.Yes its stock case. If had another case sitting here I would just do prep on it and bore right from get go.
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline bikeguy307

  • Full Member
  • ***
  • Posts: 241
    • View Profile
Re: repair for PG case
« Reply #4 on: April 23, 2015, 06:21:36 PM »
If you want a stock case I can ship you one.
Logged

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: repair for PG case
« Reply #5 on: April 23, 2015, 06:27:30 PM »
Thanks I have cpl folks looking around right now.If no luck I may take you up on that. Man these things use to be every where,not now days.
« Last Edit: April 23, 2015, 06:31:13 PM by wideopen231 »
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline bikeguy307

  • Full Member
  • ***
  • Posts: 241
    • View Profile
Re: repair for PG case
« Reply #6 on: April 23, 2015, 08:07:45 PM »
I'm a hoard!! I have dozens.
Logged

dreracecar

  • Guest
Re: repair for PG case
« Reply #7 on: April 25, 2015, 09:26:29 AM »
Trying to weld a di-cast case thats been soaking in oil is going to be a mess, Given that this is not 3am in the morning before the big race and nothing is available, quit dicking around and get another case
Logged

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1911
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: repair for PG case
« Reply #8 on: April 25, 2015, 11:01:36 AM »
Already set new caseup for him last night. Did all of the extras to make it pro tree brake,cut bell off and bored for bearing. pretty sure he got his $100 worth. Hey hes young and trying so no problem helping him out some. I knew correct thing just had to let him see others saying same thing. Sorry I kind of used you guys.Chalk it up for educating the young.
Logged
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline bikeguy307

  • Full Member
  • ***
  • Posts: 241
    • View Profile
Re: repair for PG case
« Reply #9 on: April 25, 2015, 03:52:47 PM »
Sometimes you have to lead the youngsters to the right answer! Great of you to help him out!
Logged
Pages: [1]   Go Up
« previous next »