Author Topic: Fuel for a blown Chrysler Wedge  (Read 7828 times)

Offline slingshot383

  • Full Member
  • ***
  • Posts: 146
    • View Profile
  • Your Best Time: 1/4 mi. 7.95 @ 168
  • Your Engine: Chrysler, alcohol, 528 cu.in.
  • Your Track: Gateway Motorsports Park (the Swamp)
  • Your Vehicle: Undercover Chassis 23T altered
Fuel for a blown Chrysler Wedge
« on: February 07, 2013, 01:17:14 PM »
Putting together a 528 cu. in. Chrysler Wedge engine, Indy 572-13 heads, 8-71, Mallory III mag.  I've heard that a 60/40 split of fuel for hat/ port nozzles so that the blower stays cool and for tuneability, AN16 minimum for the fuel line, and at least a 15 gallon pump.  Is this close?
Undercover 23T Altered, big block Mopar
Member of the Torque and Recoil Club

Offline Spud Miller

  • Global Moderator
  • Sr. Member
  • *****
  • Posts: 332
    • View Profile
    • Fuel Injection Ent., LLC
Re: Fuel for a blown Chrysler Wedge
« Reply #1 on: February 07, 2013, 05:50:20 PM »

 I like a 60/40 area split (hat/port) until you reach about 7 GPM through the blower (at 8000 RPM). Then I start skewing the ratio to make the ports a larger percentage. My feeling is that blowers don't compress liquid...just air. By putting too much liquid through the rotors, you're hurting output. Naturally, the bigger the blower, the more you can get away with. That's just my rule of thumb and it has worked well for me.

 The size of pump required really is determined by how fast you plan to spin that blower in this case. If you spin it straight up, you could get by with a 10 gallon pump just fine. If you're really spinning the snot out of it, a 15 or 17 gallon pump might be required to have enough bypass area left to tune with. Ultimately, it's about how much HP you're going to be making and having the fuel available to support it.

 Lots of factors determine the minimum required inlet line size...distance from tank, height above fuel level, returns on the inlet side, etc. For most deals, a -12 is ok up to 12 GPM, but a -16 would be better. Above 12 GPM, I wouldn't use less than a -16 or 1 1/4" hose.

 Spud


Fuel Injection Enterprises, LLC
     Mechanical Injection
     Magnetos
     EFI Conversions

Offline Garyr

  • Newbie
  • *
  • Posts: 3
  • SEMA chassis builder #176
    • View Profile
Re: Fuel for a blown Chrysler Wedge
« Reply #2 on: February 17, 2013, 08:12:48 AM »
Keep the -16 fuel line short or use a hard line section as the -16 AN line will collapse when used in longer sections and lean out the fuel mix. This is ahard to find problem when things happen about 1000 feet and never happen when running the 1/8.
bad decisions make great stories

Offline slingshot383

  • Full Member
  • ***
  • Posts: 146
    • View Profile
  • Your Best Time: 1/4 mi. 7.95 @ 168
  • Your Engine: Chrysler, alcohol, 528 cu.in.
  • Your Track: Gateway Motorsports Park (the Swamp)
  • Your Vehicle: Undercover Chassis 23T altered
Re: Fuel for a blown Chrysler Wedge
« Reply #3 on: February 17, 2013, 09:14:23 AM »
It's an altered, so it's not that far from tank to pump.  Add a filter, and the return line manifold, and it's shorter yet.
Undercover 23T Altered, big block Mopar
Member of the Torque and Recoil Club

Offline 23T Hemmee

  • Newbie
  • *
  • Posts: 35
    • View Profile
  • Your Best Time: 6.78 @ 196+
  • Your Engine: 557 KB-Veney Blown-alky
  • Your Track: Beech Bend-Bowling Green, KY
  • Your Vehicle: 125" Plueger 23T Altered
Re: Fuel for a blown Chrysler Wedge
« Reply #4 on: February 20, 2013, 07:00:56 AM »
Larry,
I don't know if you want a filter in your main supply line, unless its huge...too much chance for cavitation.
Ronny
Mechanical Bull
John 14:6

Offline slingshot383

  • Full Member
  • ***
  • Posts: 146
    • View Profile
  • Your Best Time: 1/4 mi. 7.95 @ 168
  • Your Engine: Chrysler, alcohol, 528 cu.in.
  • Your Track: Gateway Motorsports Park (the Swamp)
  • Your Vehicle: Undercover Chassis 23T altered
Re: Fuel for a blown Chrysler Wedge
« Reply #5 on: February 20, 2013, 03:01:05 PM »
Yep found a huge one, and was planning on making a return line manifold like I have for the stack injection.
Undercover 23T Altered, big block Mopar
Member of the Torque and Recoil Club