Author Topic: compression and bore increase hp gain?  (Read 2804 times)

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1910
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
compression and bore increase hp gain?
« on: November 07, 2023, 05:05:41 PM »
I have been looking at increasing bore and compression for boost in power over the winter,

Yes I know I will not know how much it is worth w/o some solid runs this year. Few more chances to get that info left,

Going from 4.250 bore to 4.310 or maybe 4.375 with compression increase of 12:1 to 15:1. According to desk top dyno before pc died it is worth 60 to 70 hp. Rather I go with a .250 bigger crank is up in air since requires new rods and the ones in motor are about new. At 150o a set i rather not do both. I could reinstall old rods with 128 runs but that was my change-out point for those in blower motors.
.
So question is agree or disagree with the power gain from bore and increase in compression
« Last Edit: November 08, 2023, 06:20:00 PM by wideopen231 »
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline gordon

  • Newbie
  • *
  • Posts: 43
    • View Profile
  • Your Track: Sacramento
  • Your Vehicle: FED
Re: compression and bore increase hp gain?
« Reply #1 on: November 08, 2023, 03:32:50 AM »
What is bore and stroke currently? I got lost following the numbers in your post. Also is this thing Blown Alky currently or just N/A? Other thing to consider is what is your realistic comfort zone on Max RPM on a run? Bore and stroke changes do make a difference on shape of power curve as does cam timing and head flow.

Offline JEFF/21C

  • Full Member
  • ***
  • Posts: 122
    • View Profile
  • Your Best Time: N/A
  • Your Engine: 306 SBC INJECTED ALKY
  • Your Track: NONE
  • Your Vehicle: 23 T ALTERED
  • General Location: eastern canada
Re: compression and bore increase hp gain?
« Reply #2 on: November 08, 2023, 08:17:50 AM »
I think there are typos! need more info but from I understand maybe this is a na motor on alky,bigger bore normally helps head flow and higher compression if it a result of a bigger dome sometimes impedes flow and combustion, which might require dual plug heads depending on heads  if after market heads call tech and ask questions.
Gordon is right need more info on your set-up

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1910
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: compression and bore increase hp gain?
« Reply #3 on: November 08, 2023, 06:26:04 PM »
What is bore and stroke currently? I got lost following the numbers in your post. Also is this thing Blown Alky currently or just N/A? Other thing to consider is what is your realistic comfort zone on Max RPM on a run? Bore and stroke changes do make a difference on shape of power curve as does cam timing and head flow.

4.250 going to 4.310 or 4.375 bore/ Rpm not a concern motor use to be spun at 11.000 when had screw blower on it and these rods are better than one I had then. Not going 11k probably 8500 max but 9500 would not worry me.
 Headflow is around 540 at .800 if memory serves. N?a but with nitro at times. Cam is 289/292 at .050 with .825 lift.
 Stroke is 4.250 and may drop the 4.50 in,just not wanting to buy new rods at 1500 a set and have new set. Rods are .340 over stock and could drop back to .220 over if goin g to 4.50 crank and use same pistons. With big influx, I could just build both. Anybody have more than you need?LOL at 511 and 540 ci just need money.
Compression is 12:1 going to 15:1 with .040 gasket and dwon to around 13.5: with gasket changes.
« Last Edit: November 08, 2023, 06:35:58 PM by wideopen231 »
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot

Offline gordon

  • Newbie
  • *
  • Posts: 43
    • View Profile
  • Your Track: Sacramento
  • Your Vehicle: FED
Re: compression and bore increase hp gain?
« Reply #4 on: November 09, 2023, 03:15:42 AM »
I would go to the .060 overbore of 4.310 , use your 4.250 crank with the longest rods you can hang on it and have a fairly short pin height . Compression is good for alcohol  but you do reach a point where the dome to get it starts plying xxxx with air flow and flame front. 13.5:1 sounds like a good place to start. Also if I remember right the 4.310 bore with a 4.250 stroke is 496 cu in. not 511.  Put it together and have fun. Later on if you want more put the 4.5" crank in for alot more grunt but don't buzz it past 7500-7800 max

Offline wideopen231

  • Hero Member
  • *****
  • Posts: 1910
    • View Profile
  • Your Best Time: 1/8 3.70@ 198 1/4 5.78@245
  • Your Engine: Hemi 526 ci alcohol
  • Your Track: Piedmont
  • Your Vehicle: 225 CMC FED
  • General Location: NORTH CAROLINA
Re: compression and bore increase hp gain?
« Reply #5 on: November 09, 2023, 04:40:19 AM »
511 was 4.378 with 4.25 stroke. My thinking is I can build it 15:1 and change gaskets for 13.5:. As for dome it is there no matter with a Hemi. Most of my compression gain will be in valve pockets I have a butt load of clearnace with pistons in motor  now. I think I can get to almost 14:1 with just more piston in that area, Heck right now with rods I have and pistons I had I am .020 down in hole which would be ,5 of it right there.

Oned thing about build most compression I can with .040 gasket is if lowering with gasket I move the whole chamber awa fro piston including top of dome, WOuld seem has to hel flame travel. Or so My therory goes.LOL

 Question was bout power gain and if chance desktop dyno is correct in the 60 hp to 70 hp depending on how I work cam timing.
Relecting obama is like shooting right foot because it did not hurt enough when you shot left foot