FED Classifieds

Updated monthly. Ads are removed after 3 months unless requested sooner.

FOR SALE

I have a 1950's front engine dragster complete race ready car. 1955 235 straight 6 cyl. motor ,3 spd. trans. all new build ,set up to run H.A.M.B. events or nostalgia races. Car is a HA/GR legal car runs 9.50's in the 1/8 mile @ 70 mph. Price is $4500 and can go racing this weekend with it! Erinmindyw@wmconnect.com

FOR SALE

I have 125" front engine dragster complete with balanced 350 sbc and powerglide, all moon guages and rear anson slots and spindle mount magnisum wheels. Complete $7500 Have pics of car to e-mail. Laymeadow@aol.com or call 865-385-3052

FOR SALE

Pair M&H nostalgia slicks 13 x 31.9 x 16 late 60's early 70's vintage, no marking that they are m&h only 3 molded rings in side walls. Very good to excellent condition. $200 w/tubes

Pair ET Fueler wheels 10 x 16 Olds Pont. B.P.early 70's vintage. Forged aluminum construction. Excellent condition $300 B.O.

Both great stuff for Cacklefest car . Call 585-227-3636 email ford39@localnet.com

FOR SALE

130" wheelbase FED frame and trailer. $1,500.00 or offer. E-mail any questions to eileen0707@bellsouth.net

FOR SALE

Front engine dragster, 175" W.B., all chrome-moly, chassis certified (7.50) until May 2011, Small Block Mopar drivetrain, 16 runs on the car, with the best 7.05 @ 101.5 (1/8 mile). Car is perfectly straight and in excellent condition. Will fit a 5’8”, 205 lb. driver. Excellent bracket car. $18,500 turnkey or $15,500 roller. Will deliver free within 100 miles of Pittsburgh PA. (412) 787-2948 Leave Message or fklatte@yahoo.com.

WANTED

Scotty Finn K-88 plans or old K-88 chassie, Wanted for cacklefest car, to replace long lost Ally Oop car ran West Coast in late1959, First small block chey to go 180 mph. bobsteinman@unwiredbb.com

WANTED

60’s style breather mask. Contact Gary Meyer: gmeyer@outsourcedinc.com

FOR SALE

I have a pair of american racing 15x8.5 magnesium wheels for sale with 5 on 5.5 bolt pattern. kolohe2@cox.net

FOR SALE

2004 Neil and Parks Front Engine Dragster Chassis, 210" wheel base, diagonal slip tube chassis, set up for small block and mopar as mid plate is dual drilled and have flywheel for mopar. Light wieght approx. 1400 with small block and driver. NHRA certified 6.00 and slower. Fab 9-inch with strange 12 bolt center section, lightened ring gear, aluminum spool, gundrilled axles. Light wilwood brakes, with lightest and strongest bogart wheels. Comes with air shifted shorty power glide with aluminum hipster valve body, 1.9 low gear, low pressure pump, A1 7-inch converter, CSR carbon fider full case shield. selling rolling $15,000 george.feenstra@sympatico.ca phone: 519 845 0376

WANTED

Looking for front engine dragster, roller or whatever preferably in Canada, pother@shaw.ca

TRADE

I WOULD LIKE TO TRADE 125 INCH ALTERED FOR FRONT ENGINE DRAGSTER. RUNS 5:30 IN 1/8 bobby_jones@exceedtech.net

FOR SALE

I have a class b front axle with rims/tires. If it was to be used on the strip it would need new tires(16") and bearings. I am in East Central MN(about 100 miles N. of the MPLS/ St. Paul area) Don't know how I would ship item. Item is in good condition but has minor rust on chrome steering sections of the axle and the rims. Make a reasonable offer. Eric: eschultz55795@frontiernet.net

WANTED

Looking for the whereabouts or information on this car. It is the Gerald Foster's King Cobra F/C. This is a Logghe Stamping Co. The car ran a Late Model Ed Pink Hemi. Car was campaigned in the early '70s by Sidney Foster and I and then Frank Huff and I. This picture is one of the last and most accurate I know of. Any information on this car would be greatly appreciated. Also interested in information on the "Shreve Automotive" Top Fuel Dragster driven by Dave Chenevert. This was a Don Long car full-bodied front-motored car. I believe the car was around 190 inches long and 392 powered. Information on either of these cars would be greatly appreciated. Looking for any Real SPE or Don Long Front Engine Dragsters as well as Logghe or Woody Gilmore Funny Cars. Tom Gorman tomgorman@cox.net

WANTED

Weiand 6-71 B Blower intake manifold for Big block Mopar B engine. It must be in production condition. No milled or repaired manifolds please. Contact Scott at: nastyvaliant@clearwire.net

FOR SALE

This is a quality, chromoly, 148" WB FED that has been updated and ready to receritify. It is of the late '50's early '60's era, built in the Logghe style. It is ready for a BB Mopar drivetrain and fits just about any size driver. I have owned this car since 1991, and have decided to give up racing. I was in the process of restoring the digger back to a more nostalgic look, but with common sense updates. The safety of this car has always been a prime concern.

If interested email ppleli@gmail.com for more pictures and information. Serious inquiries only, please. Or call Phil at 519-254-3188

I have countless hours of work and a far greater amount of money invested in the car than I am asking. The asking price for the rolling chassis is $7,500 or best offer. I have several BB Mopar drivetrains, and drag racing related components available for sale if the chassis gets sold.